I set up AP with MT7622.
Within around hour-two I can connect and disconnect any devices to this network. But after this time when I try new device that was not connected before it failed. No error messages in logs.
Can you check temperature with infrared thermometer on your board?
I do have a radiator stick onto CPU and memories
And sys/kernel/debug/ieee80211/phy0/temperature shows 49 deg C
But Im running rtl-sdr USB stick with wmbusmeters to read water and electricity meters. It takes constantly around 25% load of one of CPU. Also Running Home Assistance on that R64.
Did you see this connection problem on mt7615 or only on mt7622? Also, try to use unencrypted connection.
Unfortunately I do not have mt7615 so only mt7622. Will check without encryption.
Enable “force 40MHz mode”
Always use 40MHz channels even if the secondary channel overlaps. Using this option does not comply with IEEE 802.11n-2009!
We can reproduce similar issue - mobile phone from time to time it disconnects and reconnects. I will take a look at that.
Hi. I have partial success to report. Once again for completeness, I am using the BPI R64 rev 1.1 board with BPI MT7615 IPA v1.0 PCIe card in slot CN25.
I used the split pcie-nodes patch and all the other 3 patches listed in post #31 by @frank-w. I also used the eeprom.c from @niebieski20 at https://github.com/m2LiJu/BPI_R64_OpenWRT I have disabled onboard mt7622 wifi (wmac node) and BT in the R64 DTS file.
Now I get the mt7615 enumerated by pcie and dmesg shows N9 firmware and CR4 firmware get loaded by the driver.
root@OpenWrt:/# lspci
01:00.0 Class 0002: 14c3:7615
00:00.0 Class 0604: 14c3:3258
root@OpenWrt:/# ip a
1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN group default qlen 1000
link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
inet 127.0.0.1/8 scope host lo
valid_lft forever preferred_lft forever
inet6 ::1/128 scope host
valid_lft forever preferred_lft forever
2: eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc fq_codel master br-lan state UP group default qlen 1000
link/ether 06:11:8d:b7:b4:e9 brd ff:ff:ff:ff:ff:ff
3: eth1: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc fq_codel state UP group default qlen 1000
link/ether 42:5e:26:0f:2d:a1 brd ff:ff:ff:ff:ff:ff
inet6 fe80::405e:26ff:fe0f:2da1/64 scope link
valid_lft forever preferred_lft forever
5: br-lan: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc noqueue state UP group default qlen 1000
link/ether 06:11:8d:b7:b4:e9 brd ff:ff:ff:ff:ff:ff
inet 192.168.1.1/24 brd 192.168.1.255 scope global br-lan
valid_lft forever preferred_lft forever
inet6 fd98:13e6:dbdc::1/60 scope global noprefixroute
valid_lft forever preferred_lft forever
inet6 fe80::411:8dff:feb7:b4e9/64 scope link
valid_lft forever preferred_lft forever
6: wlan0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc noqueue master br-lan state UP group default qlen 1000
link/ether 00:0c:43:26:60:00 brd ff:ff:ff:ff:ff:ff
inet6 fe80::20c:43ff:fe26:6000/64 scope link
valid_lft forever preferred_lft forever
root@OpenWrt:/#
root@OpenWrt:/# dmesg|grep -E 'mtk|mt76'
[ 0.000000] Kernel command line: board=bpi-r64 console=ttyS0,115200n1 earlyprintk root=/dev/mmcblk0p2 rootfstype=ext4 rootwait service=linux debug=7 initcall_debug=0 androidboot.hardware=mt7622 swiotlb=512
[ 0.049689] mtk-tphy 1a0c4000.usb-phy: failed to get ref_clk(id-1)
[ 0.747661] mtk_soc_eth 1b100000.ethernet: generated random MAC address d2:72:9c:f8:d2:3e
[ 0.756107] mtk_soc_eth 1b100000.ethernet eth0: mediatek frame engine at 0xffffffc011520000, irq 132
[ 0.765261] mtk_soc_eth 1b100000.ethernet: generated random MAC address 9e:cb:72:29:93:7d
[ 0.773639] mtk_soc_eth 1b100000.ethernet eth1: mediatek frame engine at 0xffffffc011520000, irq 132
[ 0.817541] rtc_mt7622 10212800.rtc: registered as rtc0
[ 0.828787] mtk-thermal 1100b000.thermal: Device not calibrated, using default calibration values
[ 0.837980] mtk-wdt 10212000.watchdog: Watchdog enabled (timeout=31 sec, nowayout=0)
[ 0.898941] mtk-msdc 11240000.mmc: Got CD GPIO
[ 0.956527] mtk-pcie 1a143000.pcie: host bridge /pcie@1a143000 ranges:
[ 0.963081] mtk-pcie 1a143000.pcie: Parsing ranges property...
[ 0.968916] mtk-pcie 1a143000.pcie: MEM 0x20000000..0x27ffffff -> 0x20000000
[ 0.976246] mtk-pcie mtk_pcie_startup_port_v2. training timeout set to 1000. portbase=10afd000
[ 1.000643] mtk-pcie 1a143000.pcie: PCI host bridge to bus 0000:00
[ 1.169104] mtk-pcie 1a145000.pcie: host bridge /pcie@1a145000 ranges:
[ 1.175632] mtk-pcie 1a145000.pcie: Parsing ranges property...
[ 1.181466] mtk-pcie 1a145000.pcie: MEM 0x28000000..0x2fffffff -> 0x28000000
[ 1.188763] mtk-pcie 1a145000.pcie: IRQ index 1 not found
[ 1.194202] mtk-pcie mtk_pcie_startup_port_v2. training timeout set to 1000. portbase=10b0d000
[ 1.212728] mtk-msdc 11230000.mmc: phase: [map:3fffffff] [maxlen:30] [final:10]
[ 2.194226] mtk-pcie mtk_pcie_startup_port_v2. poll timeout. err=-110
[ 2.194234] mtk-pcie 1a145000.pcie: Port1 link down
[ 2.205657] mtk-pcie 1a145000.pcie: PCI host bridge to bus 0001:00
[ 2.239305] mtk_hsdma 1b007000.dma-controller: Using 3 as missing dma-requests property
[ 2.247485] mtk_hsdma 1b007000.dma-controller: MediaTek HSDMA driver registered
[ 7.460869] xhci-mtk 1a0c0000.usb: xHCI Host Controller
[ 7.466106] xhci-mtk 1a0c0000.usb: new USB bus registered, assigned bus number 1
[ 7.475151] xhci-mtk 1a0c0000.usb: hcc params 0x01403198 hci version 0x96 quirks 0x0000000000210010
[ 7.484221] xhci-mtk 1a0c0000.usb: irq 128, io mem 0x1a0c0000
[ 7.498340] xhci-mtk 1a0c0000.usb: xHCI Host Controller
[ 7.503570] xhci-mtk 1a0c0000.usb: new USB bus registered, assigned bus number 2
[ 7.510967] xhci-mtk 1a0c0000.usb: Host supports USB 3.0 SuperSpeed
[ 7.533589] rtc_mt7622 10212800.rtc: setting system clock to 2000-01-01T00:00:07 UTC (946684807)
[ 7.924297] mtk_soc_eth 1b100000.ethernet: PPE started
[ 7.929474] mtk_soc_eth 1b100000.ethernet eth0: configuring for fixed/2500base-x link mode
[ 7.937789] mtk_soc_eth 1b100000.ethernet eth0: Link is Up - 2.5Gbps/Full - flow control rx/tx
[ 13.192120] __pci_register_driver--> mod_name=mt7615e
[ 13.197336] mt7615e 0000:01:00.0: assign IRQ: got 137
[ 13.213059] mt7615e 0000:01:00.0: enabling device (0000 -> 0002)
[ 13.219141] mt7615e 0000:01:00.0: enabling bus mastering
[ 13.235595] __pci_register_driver--> mod_name=mt7615e ret=0
[ 13.256493] mt7615e 0000:01:00.0: HW/SW Version: 0x8a108a10, Build Time: 20180518100604a
[ 13.297006] mt7615e 0000:01:00.0: N9 Firmware Version: 2.0, Build Time: 20200131181812
[ 13.314934] mt7615e 0000:01:00.0: CR4 Firmware Version: _reserved_, Build Time: 20190121161307
[ 14.673574] mtk_soc_eth 1b100000.ethernet eth0: Link is Down
[ 14.682066] mtk_soc_eth 1b100000.ethernet: 0x100 = 0xffff9070, 0x10c = 0x100808ff
[ 14.689616] mtk_soc_eth 1b100000.ethernet: reset pse
[ 14.774577] mtk_soc_eth 1b100000.ethernet: PPE started
[ 14.779781] debugfs: Directory 'mtk_ppe' with parent '/' already present!
[ 14.786619] mtk_soc_eth 1b100000.ethernet eth0: configuring for fixed/2500base-x link mode
[ 14.794960] mtk_soc_eth 1b100000.ethernet eth0: Link is Up - 2.5Gbps/Full - flow control rx/tx
[ 14.839456] mtk_soc_eth 1b100000.ethernet eth1: configuring for fixed/rgmii link mode
[ 14.847929] mtk_soc_eth 1b100000.ethernet eth1: Link is Up - 1Gbps/Full - flow control rx/tx
root@OpenWrt:/#
F0: 102B 0000
F6: 3800 00A0
F3: 0000 0000
V0: 0000 0000 [0001]
00: 0000 0000
BP: 0000 0041 [0000]
G0: 0190 0000
T0: 0000 0335 [000F]
Jump to BL
UNIVPLL_CON0 = 0xFE000000!!!
mt_pll_init: Set pll frequency for 25M crystal
RAM_CONSOLE preloader last status: 0x0 0x0 0x0 0x0 0x0 0x0
[PMIC_WRAP]wrap_init pass,the return value=0.
[pmic_init] Preloader Start..................
[pmic_init] MT6380 CHIP Code, reg_val = 0, 1:E2 0:E3
[pmic_init] Done...................
Chip part number:7622A
MT7622 Version: 1.2.7, (iPA)
SSC OFF
mt_pll_post_init: mt_get_cpu_freq = 1350000Khz
mt_pll_post_init: mt_get_mem_freq = 1600000Khz
mt_pll_post_init: mt_get_bus_freq = 1119920Khz
[PLFM] Init I2C: OK(0)
I don’t know how to enable radio and setup wifi from the command line. So using a wired ethernet connection between my laptop and R64, I access LUCI from the browser. I setup the wifi with no encryption.
The radio shows only 802.11 modes of “Legacy” or “N”. No “AC”.
I am then able to connect my laptop to that SSID. But that is about it. The BPI-R64 completely freezes. The console shell is frozen too. After about 15-30sec, it shows the bootloader messages and brings back to the BL bootmenu.
This is now new realm for me to debug further. @sinovoip, can you help in any way to resolve this?
@frank-w, have you gotten R64 and MT7615 PCIe card to work satisfactorily with debian? I would prefer to use openwrt. But if there is a working version with Debian, I think I can learn the ropes to setup debian based router.
Thanks.
I have no mt7615 card…but tested an mt7612 and ath10k some time ago (imho before 5.4 was out)
I used mt7622 AP to connect / disconnect continuously with my mobile phone for hours, but couldn’t reproduce that connection issue. BTW, could you please enable the firmware debug log after boot up? Need to check if client is added/removed to/from staList correctly every time.
echo 2 > /sys/kernel/debug/ieee80211/phy1/mt76/fw_debug
[ 1918.379565] ieee80211 phy0: N9: (00062404577)StaRec[1] is added for staList
[ 1918.386614] ieee80211 phy0: N9: (00062404578)StaRec1 Tag 0x9
[ 1918.392444] ieee80211 phy0: N9: (00062404580)StaRec1 Tag 0xd
[ 1918.398268] ieee80211 phy0: N9: (00062404581)WTBL# Idx 1 Op 1
[ 1926.659687] ieee80211 phy0: N9: (00062676068)StaRec1 Tag 0x0
[ 1926.665522] ieee80211 phy0: N9: (00062676077)StaRec[1] is removed from staList
1 Like
Hi, I guess the root cause is MSI. please try this patch https://patchwork.kernel.org/patch/11494641/
@Ryder.Lee Attached logs from FW.
MT7622_WIFI_FW_debug.7z (40.7 KB)
I restart R64 overnight and at the morning I was not able to connect to wifi even with devices that was connected before. If need more tests I will leave it running in that state for next few hours.
Thanks. I’ve co-worked with @Kosyak to reduce debugging scope today (in mt76-devel irc channel). I will make a patch to check sta_add flow soon.
I’m trying to include the patch you mentioned in the build, but my knowledge and understanding is simply not enough to get things right.
I had to make some modifications to the patch itself since it failed to apply to mt7622-rfb1.dts. I rewrote the section this way:
diff --git a/arch/arm64/boot/dts/mediatek/mt7622-rfb1.dts b/arch/arm64/boot/dts/mediatek/mt7622-rfb1.dts
index 3f783348c66a..2e6b4e37cb7d 100644
--- a/arch/arm64/boot/dts/mediatek/mt7622-rfb1.dts
+++ b/arch/arm64/boot/dts/mediatek/mt7622-rfb1.dts
@@ -244,18 +244,10 @@
};
};
-&pcie {
+&pcie0 {
pinctrl-names = "default";
- pinctrl-0 = <&pcie0_pins>, <&pcie1_pins>;
+ pinctrl-0 = <&pcie0_pins>;
status = "okay";
-
- pcie@0,0 {
- status = "okay";
- };
-
- pcie@1,0 {
- status = "okay";
- };
};
&pio {
But now I have this error upon build:
Error: /home/parallels/bpi-r64/openwrt/build_dir/target-aarch64_cortex-a53_musl/linux-mediatek_mt7622/linux-5.4.42/arch/arm64/boot/dts/mediatek/mt7622-elecom-wrc-2533gent.dts:168.1-6 Label or path pcie not found
FATAL ERROR: Syntax error parsing input tree
I figure it’s due to the following section in the mt7622-elecom-wrc-2533gent.dts file, but I don’t know what should I write there instead.
&pcie {
pinctrl-names = "default", "pcie1_pins";
pinctrl-0 = <&pcie0_pins>;
pinctrl-1 = <&pcie1_pins>;
status = "okay";
pcie@0,0 {
status = "okay";
mt7615@0,0 {
reg = <0x0000 0 0 0 0>;
mediatek,mtd-eeprom = <&factory 0x05000>;
};
};
};
&pcie should probably be renamed to &pcie0 but what to do with the other lines?
Any advice?
Why not just disable the block with /* */ ? This dts is not needed for r64
Thank you. I renamed &pcie to &pcie0 just to make it compile.
But now it looks like that I’ve lost mk7615e completely.
Starting kernel ...
[ATF][ 23.907478]save kernel info
[ATF][ 23.910680]Kernel_EL2
[ATF][ 23.913436]Kernel is 64Bit
[ATF][ 23.916624]pc=0x41080000, r0=0x6bff6000, r1=0x0
INFO: BL3-1: Preparing for EL3 exit to normal world, Kernel
INFO: BL3-1: Next image address = 0x41080000
INFO: BL3-1: Next image spsr = 0x3c9
[ATF][ 23.934890]el3_exit
[ 0.000000] Booting Linux on physical CPU 0x0000000000 [0x410fd034]
[ 0.000000] Linux version 5.4.42 ([email protected]) (gcc version 8.4.0 (OpenWrt GCC 8.4.0 r13342-e35e40ad82)) #0 SMP Sat May 20
[ 0.000000] Machine model: Bananapi BPI-R64
[ 0.000000] On node 0 totalpages: 262096
[ 0.000000] DMA32 zone: 4096 pages used for memmap
[ 0.000000] DMA32 zone: 0 pages reserved
[ 0.000000] DMA32 zone: 262096 pages, LIFO batch:63
[ 0.000000] psci: probing for conduit method from DT.
[ 0.000000] psci: PSCIv0.2 detected in firmware.
[ 0.000000] psci: Using standard PSCI v0.2 function IDs
[ 0.000000] psci: Trusted OS migration not required
[ 0.000000] percpu: Embedded 20 pages/cpu s43608 r8192 d30120 u81920
[ 0.000000] pcpu-alloc: s43608 r8192 d30120 u81920 alloc=20*4096
[ 0.000000] pcpu-alloc: [0] 0 [0] 1
[ 0.000000] Detected VIPT I-cache on CPU0
[ 0.000000] CPU features: kernel page table isolation disabled by kernel configuration
[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 258000
[ 0.000000] Kernel command line: board=bpi-r64 console=ttyS0,115200n1 earlyprintk root=/dev/mmcblk0p2 rootfstype=ext4 rootwait servi2
[ 0.000000] Dentry cache hash table entries: 131072 (order: 8, 1048576 bytes, linear)
[ 0.000000] Inode-cache hash table entries: 65536 (order: 7, 524288 bytes, linear)
[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
[ 0.000000] Memory: 1018396K/1048384K available (6590K kernel code, 432K rwdata, 1896K rodata, 448K init, 285K bss, 29988K reserved,)
[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
[ 0.000000] rcu: Hierarchical RCU implementation.
[ 0.000000] rcu: CONFIG_RCU_FANOUT set to non-default value of 32.
[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 25 jiffies.
[ 0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0
[ 0.000000] GIC: GICv2 detected, but range too small and irqchip.gicv2_force_probe not set
[ 0.000000] random: get_random_bytes called from start_kernel+0x2d4/0x430 with crng_init=0
[ 0.000000] arch_timer: cp15 timer(s) running at 12.50MHz (phys).
[ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x2e2049cda, max_idle_ns: 440795202628 ns
[ 0.000003] sched_clock: 56 bits at 12MHz, resolution 80ns, wraps every 4398046511080ns
[ 0.000169] Calibrating delay loop (skipped), value calculated using timer frequency.. 25.00 BogoMIPS (lpj=50000)
[ 0.000176] pid_max: default: 32768 minimum: 301
[ 0.000262] Mount-cache hash table entries: 2048 (order: 2, 16384 bytes, linear)
[ 0.000272] Mountpoint-cache hash table entries: 2048 (order: 2, 16384 bytes, linear)
[ 0.001153] ASID allocator initialised with 65536 entries
[ 0.001202] rcu: Hierarchical SRCU implementation.
[ 0.001462] smp: Bringing up secondary CPUs ...
[ 0.001778] Detected VIPT I-cache on CPU1
[ 0.001815] CPU1: Booted secondary processor 0x0000000001 [0x410fd034]
[ 0.001869] smp: Brought up 1 node, 2 CPUs
[ 0.001875] SMP: Total of 2 processors activated.
[ 0.001879] CPU features: detected: 32-bit EL0 Support
[ 0.001883] CPU features: detected: CRC32 instructions
[ 0.001984] CPU: All CPU(s) started at EL2
[ 0.001993] alternatives: patching kernel code
[ 0.005269] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns
[ 0.005283] futex hash table entries: 512 (order: 3, 32768 bytes, linear)
[ 0.005374] pinctrl core: initialized pinctrl subsystem
[ 0.005801] NET: Registered protocol family 16
[ 0.006082] DMA: preallocated 256 KiB pool for atomic allocations
[ 0.017038] GPIO line 499 (asm_sel) hogged as output/high
[ 0.029753] SCSI subsystem initialized
[ 0.029903] libata version 3.00 loaded.
[ 0.030037] usbcore: registered new interface driver usbfs
[ 0.030063] usbcore: registered new interface driver hub
[ 0.030090] usbcore: registered new device driver usb
[ 0.030865] Bluetooth: Core ver 2.22
[ 0.030899] NET: Registered protocol family 31
[ 0.030902] Bluetooth: HCI device and connection manager initialized
[ 0.030910] Bluetooth: HCI socket layer initialized
[ 0.030916] Bluetooth: L2CAP socket layer initialized
[ 0.030927] Bluetooth: SCO socket layer initialized
[ 0.031408] clocksource: Switched to clocksource arch_sys_counter
[ 0.031880] thermal_sys: Registered thermal governor 'fair_share'
[ 0.031882] thermal_sys: Registered thermal governor 'bang_bang'
[ 0.031887] thermal_sys: Registered thermal governor 'step_wise'
[ 0.031890] thermal_sys: Registered thermal governor 'user_space'
[ 0.031894] thermal_sys: Registered thermal governor 'power_allocator'
[ 0.032150] NET: Registered protocol family 2
[ 0.032419] tcp_listen_portaddr_hash hash table entries: 512 (order: 1, 8192 bytes, linear)
[ 0.032438] TCP established hash table entries: 8192 (order: 4, 65536 bytes, linear)
[ 0.032489] TCP bind hash table entries: 8192 (order: 5, 131072 bytes, linear)
[ 0.032594] TCP: Hash tables configured (established 8192 bind 8192)
[ 0.032680] UDP hash table entries: 512 (order: 2, 16384 bytes, linear)
[ 0.032701] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes, linear)
[ 0.032794] NET: Registered protocol family 1
[ 0.032813] PCI: CLS 0 bytes, default 64
[ 0.033576] workingset: timestamp_bits=46 max_order=18 bucket_order=0
[ 0.036898] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.036909] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 0.050240] mtk-tphy 1a0c4000.usb-phy: failed to get ref_clk(id-1)
[ 0.053430] mt-pmic-pwrap 10001000.pwrap: unexpected interrupt int=0x1
[ 0.067414] Serial: 8250/16550 driver, 3 ports, IRQ sharing disabled
[ 0.068049] printk: console [ttyS0] disabled
[ 0.088395] 11002000.serial: ttyS0 at MMIO 0x11002000 (irq = 118, base_baud = 1562500) is a ST16650V2
[ 0.629806] printk: console [ttyS0] enabled
[ 0.654669] 11004000.serial: ttyS1 at MMIO 0x11004000 (irq = 119, base_baud = 1562500) is a ST16650V2
[ 0.664352] 1100c000.serial: ttyS2 at MMIO 0x1100c000 (irq = 125, base_baud = 17499995) is a MediaTek BTIF
[ 0.674087] serial serial0: tty port ttyS2 registered
[ 0.679345] cacheinfo: Unable to detect cache hierarchy for CPU 0
[ 0.686878] libphy: Fixed MDIO Bus: probed
[ 0.714308] libphy: mdio: probed
[ 0.717576] mtk_soc_eth 1b100000.ethernet: generated random MAC address 6a:da:5c:29:1b:ae
[ 0.726019] mtk_soc_eth 1b100000.ethernet eth0: mediatek frame engine at 0xffffffc011500000, irq 134
[ 0.735173] mtk_soc_eth 1b100000.ethernet: generated random MAC address 66:08:0e:1e:72:8a
[ 0.743555] mtk_soc_eth 1b100000.ethernet eth1: mediatek frame engine at 0xffffffc011500000, irq 134
[ 0.752764] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 0.759288] ehci-pci: EHCI PCI platform driver
[ 0.763758] ehci-platform: EHCI generic platform driver
[ 0.769092] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 0.775295] ohci-platform: OHCI generic platform driver
[ 0.781056] usbcore: registered new interface driver usb-storage
[ 0.787444] rtc_mt7622 10212800.rtc: registered as rtc0
[ 0.793327] Driver for 1-wire Dallas network protocol.
[ 0.798682] mtk-thermal 1100b000.thermal: Device not calibrated, using default calibration values
[ 0.807869] mtk-wdt 10212000.watchdog: Watchdog enabled (timeout=31 sec, nowayout=0)
[ 0.815701] Bluetooth: HCI UART driver ver 2.3
[ 0.820142] Bluetooth: HCI UART protocol H4 registered
[ 0.825275] Bluetooth: HCI UART protocol BCSP registered
[ 0.830633] Bluetooth: HCI UART protocol Broadcom registered
[ 0.836306] Bluetooth: HCI UART protocol QCA registered
[ 0.867736] mtk-msdc 11240000.mmc: Got CD GPIO
[ 0.897879] NET: Registered protocol family 10
[ 0.902965] Segment Routing with IPv6
[ 0.906676] NET: Registered protocol family 17
[ 0.911139] 8021q: 802.1Q VLAN Support v1.8
[ 0.925745] mtk-pcie 1a143000.pcie: host bridge /pcie@1a143000 ranges:
[ 0.932298] mtk-pcie 1a143000.pcie: Parsing ranges property...
[ 0.938134] mtk-pcie 1a143000.pcie: MEM 0x20000000..0x27ffffff -> 0x20000000
[ 0.988509] mtk-msdc 11230000.mmc: phase: [map:fffffff] [maxlen:28] [final:9]
[ 0.996416] mmc0: new HS200 MMC card at address 0001
[ 1.002539] mmcblk0: mmc0:0001 008G30 7.28 GiB
[ 1.007975] mmcblk0boot0: mmc0:0001 008G30 partition 1 4.00 MiB
[ 1.014791] mmcblk0boot1: mmc0:0001 008G30 partition 2 4.00 MiB
[ 1.020775] mmcblk0rpmb: mmc0:0001 008G30 partition 3 4.00 MiB, chardev (250:0)
[ 1.029282] mmcblk0: p1 p2
[ 1.045492] mtk-pcie 1a143000.pcie: Port0 link down
[ 1.050519] mtk-pcie 1a143000.pcie: PCI host bridge to bus 0000:00
[ 1.056707] pci_bus 0000:00: root bus resource [bus 00-ff]
[ 1.062190] pci_bus 0000:00: root bus resource [mem 0x20000000-0x27ffffff]
[ 1.069061] pci_bus 0000:00: scanning bus
[ 1.074279] pci_bus 0000:00: fixups for bus
[ 1.078459] pci_bus 0000:00: bus scan returning with max=00
[ 1.084251] mtk-pcie 1a145000.pcie: host bridge /pcie@1a145000 ranges:
[ 1.090783] mtk-pcie 1a145000.pcie: Parsing ranges property...
[ 1.096623] mtk-pcie 1a145000.pcie: MEM 0x28000000..0x2fffffff -> 0x28000000
[ 1.103932] mtk-pcie 1a145000.pcie: IRQ index 1 not found
[ 1.209357] mtk-pcie 1a145000.pcie: Port1 link down
[ 1.214328] mtk-pcie 1a145000.pcie: PCI host bridge to bus 0001:00
[ 1.220510] pci_bus 0001:00: root bus resource [bus 00-ff]
[ 1.225993] pci_bus 0001:00: root bus resource [mem 0x28000000-0x2fffffff]
[ 1.232864] pci_bus 0001:00: scanning bus
[ 1.238011] pci_bus 0001:00: fixups for bus
[ 1.242193] pci_bus 0001:00: bus scan returning with max=00
[ 1.247885] mtk_hsdma 1b007000.dma-controller: Using 3 as missing dma-requests property
[ 1.256068] mtk_hsdma 1b007000.dma-controller: MediaTek HSDMA driver registered
[ 1.827418] mt753x gsw@0: LAN/WAN VLAN setting=wllll
[ 1.832837] mt753x gsw@0: Switch is MediaTek MT7531BE rev 0
[ 6.474879] xhci-mtk 1a0c0000.usb: xHCI Host Controller
[ 6.480115] xhci-mtk 1a0c0000.usb: new USB bus registered, assigned bus number 1
[ 6.489162] xhci-mtk 1a0c0000.usb: hcc params 0x01403198 hci version 0x96 quirks 0x0000000000210010
[ 6.498233] xhci-mtk 1a0c0000.usb: irq 130, io mem 0x1a0c0000
[ 6.504368] hub 1-0:1.0: USB hub found
[ 6.508134] hub 1-0:1.0: 2 ports detected
[ 6.512354] xhci-mtk 1a0c0000.usb: xHCI Host Controller
[ 6.517584] xhci-mtk 1a0c0000.usb: new USB bus registered, assigned bus number 2
[ 6.524980] xhci-mtk 1a0c0000.usb: Host supports USB 3.0 SuperSpeed
[ 6.531274] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM.
[ 6.539587] hub 2-0:1.0: USB hub found
[ 6.543340] hub 2-0:1.0: 1 port detected
[ 6.547600] rtc_mt7622 10212800.rtc: setting system clock to 2020-05-29T11:36:50 UTC (1590752210)
[ 6.562687] EXT4-fs (mmcblk0p2): mounted filesystem with ordered data mode. Opts: (null)
[ 6.570845] VFS: Mounted root (ext4 filesystem) readonly on device 179:2.
[ 6.577818] Freeing unused kernel memory: 448K
[ 6.587407] Run /sbin/init as init process
[ 6.640761] init: Console is alive
[ 6.644264] init: - watchdog -
[ 6.683513] random: fast init done
[ 6.769251] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[ 6.782971] ehci-fsl: Freescale EHCI Host controller driver
[ 6.793066] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
[ 6.808844] init: - preinit -
[ 6.889308] mtk_soc_eth 1b100000.ethernet: PPE started
[ 6.894490] mtk_soc_eth 1b100000.ethernet eth0: configuring for fixed/2500base-x link mode
[ 6.902809] mtk_soc_eth 1b100000.ethernet eth0: Link is Up - 2.5Gbps/Full - flow control rx/tx
Press the [f] key and hit [enter] to enter failsafe mode
Press [ 6.919436] usb 1-2: new high-speed USB device number 2 using xhci-mtk
the [1], [2], [3] or [4] key and hit [enter] to select the debug level
[ 7.147106] usb-storage 1-2:1.0: USB Mass Storage device detected
[ 7.153441] random: procd: uninitialized urandom read (4 bytes read)
[ 7.153468] scsi host0: usb-storage 1-2:1.0
[ 8.197074] scsi 0:0:0:0: Direct-Access JetFlash Transcend 4GB 8.07 PQ: 0 ANSI: 2
[ 8.206292] sd 0:0:0:0: [sda] 7847936 512-byte logical blocks: (4.02 GB/3.74 GiB)
[ 8.213936] sd 0:0:0:0: [sda] Write Protect is off
[ 8.218728] sd 0:0:0:0: [sda] Mode Sense: 03 00 00 00
[ 8.223917] sd 0:0:0:0: [sda] No Caching mode page found
[ 8.229231] sd 0:0:0:0: [sda] Assuming drive cache: write through
[ 8.422453] sda: sda1
[ 8.425753] sd 0:0:0:0: [sda] Attached SCSI removable disk
[ 10.936852] mount_root: mounting /dev/root
[ 10.942710] EXT4-fs (mmcblk0p2): re-mounted. Opts: (null)
[ 10.948232] mount_root: loading kmods from internal overlay
[ 10.962171] kmodloader: loading kernel modules from //etc/modules-boot.d/*
[ 10.969796] kmodloader: done loading kernel modules from //etc/modules-boot.d/*
[ 11.097395] urandom-seed: Seed file not found (/etc/urandom.seed)
[ 11.110282] procd: - early -
[ 11.113237] procd: - watchdog -
[ 11.631049] procd: - watchdog -
[ 11.634313] procd: - ubus -
[ 11.641140] random: ubusd: uninitialized urandom read (4 bytes read)
[ 11.687434] random: ubusd: uninitialized urandom read (4 bytes read)
[ 11.693899] random: ubusd: uninitialized urandom read (4 bytes read)
[ 11.700507] procd: - init -
Please press Enter to activate this console.
[ 11.781378] urngd: v1.0.2 started.
[ 11.801564] kmodloader: loading kernel modules from /etc/modules.d/*
[ 11.807706] random: crng init done
[ 11.811324] random: 6 urandom warning(s) missed due to ratelimiting
[ 11.825835] tun: Universal TUN/TAP device driver, 1.6
[ 11.841368] cryptodev: driver 1.10 loaded.
[ 11.848235] i2c /dev entries driver
[ 11.858441] hidraw: raw HID events driver (C) Jiri Kosina
[ 11.866060] Mirror/redirect action on
[ 11.873352] u32 classifier
[ 11.876092] input device check on
[ 11.879749] Actions configured
[ 11.900076] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[ 11.905411] Bluetooth: BNEP filters: protocol multicast
[ 11.910643] Bluetooth: BNEP socket layer initialized
[ 11.917486] usbcore: registered new interface driver btusb
[ 11.923904] usbcore: registered new interface driver cdc_wdm
[ 11.930150] Loading modules backported from Linux version v5.7-rc3-0-g6a8b55ed4056
[ 11.937735] Backport generated by backports.git v5.7-rc3-1-0-gc0c7d2bb
[ 11.945442] Bluetooth: HIDP (Human Interface Emulation) ver 1.2
[ 11.951393] Bluetooth: HIDP socket layer initialized
[ 11.966364] Bluetooth: RFCOMM TTY layer initialized
[ 11.971285] Bluetooth: RFCOMM socket layer initialized
[ 11.976438] Bluetooth: RFCOMM ver 1.11
[ 11.981809] usbcore: registered new interface driver ums-alauda
[ 11.988284] usbcore: registered new interface driver ums-cypress
[ 11.994636] usbcore: registered new interface driver ums-datafab
[ 12.000938] usbcore: registered new interface driver ums-freecom
[ 12.007256] usbcore: registered new interface driver ums-isd200
[ 12.013484] usbcore: registered new interface driver ums-jumpshot
[ 12.019863] usbcore: registered new interface driver ums-karma
[ 12.026067] usbcore: registered new interface driver ums-sddr09
[ 12.032307] usbcore: registered new interface driver ums-sddr55
[ 12.038592] usbcore: registered new interface driver ums-usbat
[ 12.048576] wireguard: WireGuard 1.0.20200520 loaded. See www.wireguard.com for information.
[ 12.057034] wireguard: Copyright (C) 2015-2019 Jason A. Donenfeld <[email protected]>. All Rights Reserved.
[ 12.076533] xt_time: kernel timezone is -0000
[ 12.081505] usbcore: registered new interface driver cdc_ether
[ 12.139656] mt7622-wmac 18000000.wmac: Invalid MAC address, using random address fa:2c:f2:67:82:e2
[ 12.149686] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
[ 12.172091] PPP generic driver version 2.4.2
[ 12.177543] NET: Registered protocol family 24
[ 12.183392] usbcore: registered new interface driver qmi_wwan
[ 12.189357] mt7622-wmac 18000000.wmac: HW/SW Version: 0x8a108a10, Build Time: 20190801210006a
[ 12.189357]
[ 12.200925] kmodloader: done loading kernel modules from /etc/modules.d/*
[ 12.219505] mt7622-wmac 18000000.wmac: N9 Firmware Version: 2.0, Build Time: 20200131180931
[ 18.416722] mtk_soc_eth 1b100000.ethernet eth0: Link is Down
[ 18.425276] mtk_soc_eth 1b100000.ethernet: 0x100 = 0xffff9070, 0x10c = 0x100808ff
[ 18.432804] mtk_soc_eth 1b100000.ethernet: reset pse
[ 18.522186] mtk_soc_eth 1b100000.ethernet: PPE started
[ 18.527423] debugfs: Directory 'mtk_ppe' with parent '/' already present!
[ 18.534270] mtk_soc_eth 1b100000.ethernet eth0: configuring for fixed/2500base-x link mode
[ 18.542799] mtk_soc_eth 1b100000.ethernet eth0: Link is Up - 2.5Gbps/Full - flow control rx/tx
[ 18.552071] br-lan: port 1(eth0) entered blocking state
[ 18.557369] br-lan: port 1(eth0) entered disabled state
[ 18.562825] device eth0 entered promiscuous mode
[ 18.573352] br-lan: port 1(eth0) entered blocking state
[ 18.578610] br-lan: port 1(eth0) entered forwarding state
[ 18.589158] mtk_soc_eth 1b100000.ethernet eth1: configuring for fixed/rgmii link mode
[ 18.597171] mtk_soc_eth 1b100000.ethernet eth1: Link is Up - 1Gbps/Full - flow control rx/tx
And here is iw dev output
root@OpenWrt:/# iw dev
phy#0
Interface wlan0
ifindex 4
wdev 0x1
addr fa:2c:f2:67:82:e2
type managed
txpower 6.00 dBm
multicast TXQ:
qsz-byt qsz-pkt flows drops marks overlmt hashcol tx-bytes tx-packets
0 0 0 0 0 0 0 0 0you have an bpi-r64, right? not the reference-board or the elecom…
then you need to look in the mt7622-bananapi-r64.dts if the pcie0/1 are enabled. show us output of lspci
lspci is empty. I had to recompile once again to include busybox.
mt7622-bananapi-bpi-r64.dts is as follows.
/*
* Copyright (c) 2018 MediaTek Inc.
* Author: Ryder Lee <[email protected]>
*
* SPDX-License-Identifier: (GPL-2.0 OR MIT)
*/
/dts-v1/;
#include <dt-bindings/input/input.h>
#include <dt-bindings/gpio/gpio.h>
#include "mt7622.dtsi"
#include "mt6380.dtsi"
/ {
model = "Bananapi BPI-R64";
compatible = "bananapi,bpi-r64", "mediatek,mt7622";
aliases {
serial0 = &uart0;
};
chosen {
stdout-path = "serial0:115200n8";
bootargs = "earlycon=uart8250,mmio32,0x11002000 console=ttyS0,115200n1 swiotlb=512 debug loglevel=7 rootfstype=squashfs,ext4 earlyprintk block2mtd.block2mtd=/dev/mmcblk0,65536,eMMC,5 mtdparts=eMMC:768k(preloader)ro,512k(uboot),512k(uboot-env),256k(Factory),64M(firmware),2048M(usrdata)";
};
cpus {
cpu@0 {
proc-supply = <&mt6380_vcpu_reg>;
sram-supply = <&mt6380_vm_reg>;
};
cpu@1 {
proc-supply = <&mt6380_vcpu_reg>;
sram-supply = <&mt6380_vm_reg>;
};
};
gpio-keys {
compatible = "gpio-keys";
factory {
label = "factory";
linux,code = <BTN_0>;
gpios = <&pio 0 GPIO_ACTIVE_HIGH>;
};
wps {
label = "wps";
linux,code = <KEY_WPS_BUTTON>;
gpios = <&pio 102 GPIO_ACTIVE_HIGH>;
};
};
gsw: gsw@0 {
compatible = "mediatek,mt753x";
mediatek,ethsys = <ðsys>;
#address-cells = <1>;
#size-cells = <0>;
};
leds {
compatible = "gpio-leds";
green {
label = "bpi-r64:pio:green";
gpios = <&pio 89 GPIO_ACTIVE_HIGH>;
default-state = "off";
};
red {
label = "bpi-r64:pio:red";
gpios = <&pio 88 GPIO_ACTIVE_HIGH>;
default-state = "off";
};
};
memory {
reg = <0 0x40000000 0 0x40000000>;
};
reg_1p8v: regulator-1p8v {
compatible = "regulator-fixed";
regulator-name = "fixed-1.8V";
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
regulator-always-on;
};
reg_3p3v: regulator-3p3v {
compatible = "regulator-fixed";
regulator-name = "fixed-3.3V";
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
regulator-boot-on;
regulator-always-on;
};
reg_5v: regulator-5v {
compatible = "regulator-fixed";
regulator-name = "fixed-5V";
regulator-min-microvolt = <5000000>;
regulator-max-microvolt = <5000000>;
regulator-boot-on;
regulator-always-on;
};
};
&bch {
status = "disabled";
};
&btif {
status = "okay";
};
&cir {
pinctrl-names = "default";
pinctrl-0 = <&irrx_pins>;
status = "okay";
};
ð {
status = "okay";
gmac0: mac@0 {
compatible = "mediatek,eth-mac";
reg = <0>;
phy-mode = "2500base-x";
fixed-link {
speed = <2500>;
full-duplex;
pause;
};
};
gmac1: mac@1 {
compatible = "mediatek,eth-mac";
reg = <1>;
phy-mode = "rgmii";
fixed-link {
speed = <1000>;
full-duplex;
pause;
};
};
mdio: mdio-bus {
#address-cells = <1>;
#size-cells = <0>;
};
};
&gsw {
mediatek,mdio = <&mdio>;
mediatek,portmap = "wllll";
mediatek,mdio_master_pinmux = <0>;
reset-gpios = <&pio 54 0>;
interrupt-parent = <&pio>;
interrupts = <53 IRQ_TYPE_LEVEL_HIGH>;
status = "okay";
port5: port@5 {
compatible = "mediatek,mt753x-port";
reg = <5>;
phy-mode = "rgmii";
fixed-link {
speed = <1000>;
full-duplex;
};
};
port6: port@6 {
compatible = "mediatek,mt753x-port";
reg = <6>;
phy-mode = "sgmii";
fixed-link {
speed = <2500>;
full-duplex;
};
};
};
&i2c1 {
pinctrl-names = "default";
pinctrl-0 = <&i2c1_pins>;
status = "okay";
};
&i2c2 {
pinctrl-names = "default";
pinctrl-0 = <&i2c2_pins>;
status = "okay";
};
&mmc0 {
pinctrl-names = "default", "state_uhs";
pinctrl-0 = <&emmc_pins_default>;
pinctrl-1 = <&emmc_pins_uhs>;
status = "okay";
bus-width = <8>;
max-frequency = <50000000>;
cap-mmc-highspeed;
mmc-hs200-1_8v;
vmmc-supply = <®_3p3v>;
vqmmc-supply = <®_1p8v>;
assigned-clocks = <&topckgen CLK_TOP_MSDC30_0_SEL>;
assigned-clock-parents = <&topckgen CLK_TOP_UNIV48M>;
non-removable;
emmc@0 {
#address-cells = <1>;
#size-cells = <1>;
compatible = "mmc-card";
reg = <0>;
partitions {
compatible = "fixed-partitions";
#address-cells = <1>;
#size-cells = <1>;
partition@0 {
label = "preloader";
reg = <0x0000000 0x000c0000>;
read-only;
};
partition@c0000 {
label = "uboot";
reg = <0x00c0000 0x00140000>;
};
partition@140000 {
label = "uboot-env";
reg = <0x0140000 0x001c0000>;
};
factory: partition@1c0000 {
label = "Factory";
reg = <0x01c0000 0x00200000>;
};
partition@200000 {
label = "firmware";
reg = <0x0200000 0x02200000>;
};
partition@2200000 {
label = "usrdata";
reg = <0x2200000 0x82200000>;
};
};
};
};
&mmc1 {
pinctrl-names = "default", "state_uhs";
pinctrl-0 = <&sd0_pins_default>;
pinctrl-1 = <&sd0_pins_uhs>;
status = "okay";
bus-width = <4>;
max-frequency = <50000000>;
cap-sd-highspeed;
r_smpl = <1>;
cd-gpios = <&pio 81 GPIO_ACTIVE_LOW>;
vmmc-supply = <®_3p3v>;
vqmmc-supply = <®_3p3v>;
assigned-clocks = <&topckgen CLK_TOP_MSDC30_1_SEL>;
assigned-clock-parents = <&topckgen CLK_TOP_UNIV48M>;
};
&nandc {
pinctrl-names = "default";
pinctrl-0 = <¶llel_nand_pins>;
status = "disabled";
};
&nor_flash {
pinctrl-names = "default";
pinctrl-0 = <&spi_nor_pins>;
status = "disabled";
flash@0 {
compatible = "jedec,spi-nor";
reg = <0>;
};
};
&pcie0 {
pinctrl-names = "default";
pinctrl-0 = <&pcie0_pins>;
status = "okay";
};
&pcie1 {
pinctrl-names = "default";
pinctrl-0 = <&pcie1_pins>;
status = "okay";
};
&pio {
/* Attention: GPIO 90 is used to switch between PCIe@1,0 and
* SATA functions. i.e. output-high: PCIe, output-low: SATA
*/
asm_sel {
gpio-hog;
gpios = <90 GPIO_ACTIVE_HIGH>;
output-high;
};
/* eMMC is shared pin with parallel NAND */
emmc_pins_default: emmc-pins-default {
mux {
function = "emmc", "emmc_rst";
groups = "emmc";
};
/* "NDL0","NDL1","NDL2","NDL3","NDL4","NDL5","NDL6","NDL7",
* "NRB","NCLE" pins are used as DAT0,DAT1,DAT2,DAT3,DAT4,
* DAT5,DAT6,DAT7,CMD,CLK for eMMC respectively
*/
conf-cmd-dat {
pins = "NDL0", "NDL1", "NDL2",
"NDL3", "NDL4", "NDL5",
"NDL6", "NDL7", "NRB";
input-enable;
bias-pull-up;
};
conf-clk {
pins = "NCLE";
bias-pull-down;
};
};
emmc_pins_uhs: emmc-pins-uhs {
mux {
function = "emmc";
groups = "emmc";
};
conf-cmd-dat {
pins = "NDL0", "NDL1", "NDL2",
"NDL3", "NDL4", "NDL5",
"NDL6", "NDL7", "NRB";
input-enable;
drive-strength = <4>;
bias-pull-up;
};
conf-clk {
pins = "NCLE";
drive-strength = <4>;
bias-pull-down;
};
};
eth_pins: eth-pins {
mux {
function = "eth";
groups = "mdc_mdio", "rgmii_via_gmac2";
};
};
i2c1_pins: i2c1-pins {
mux {
function = "i2c";
groups = "i2c1_0";
};
};
i2c2_pins: i2c2-pins {
mux {
function = "i2c";
groups = "i2c2_0";
};
};
i2s1_pins: i2s1-pins {
mux {
function = "i2s";
groups = "i2s_out_mclk_bclk_ws",
"i2s1_in_data",
"i2s1_out_data";
};
conf {
pins = "I2S1_IN", "I2S1_OUT", "I2S_BCLK",
"I2S_WS", "I2S_MCLK";
drive-strength = <12>;
bias-pull-down;
};
};
irrx_pins: irrx-pins {
mux {
function = "ir";
groups = "ir_1_rx";
};
};
irtx_pins: irtx-pins {
mux {
function = "ir";
groups = "ir_1_tx";
};
};
/* Parallel nand is shared pin with eMMC */
parallel_nand_pins: parallel-nand-pins {
mux {
function = "flash";
groups = "par_nand";
};
};
pcie0_pins: pcie0-pins {
mux {
function = "pcie";
groups = "pcie0_pad_perst",
"pcie0_1_waken",
"pcie0_1_clkreq";
};
};
pcie1_pins: pcie1-pins {
mux {
function = "pcie";
groups = "pcie1_pad_perst",
"pcie1_0_waken",
"pcie1_0_clkreq";
};
};
pmic_bus_pins: pmic-bus-pins {
mux {
function = "pmic";
groups = "pmic_bus";
};
};
pwm7_pins: pwm1-2-pins {
mux {
function = "pwm";
groups = "pwm_ch7_2";
};
};
wled_pins: wled-pins {
mux {
function = "led";
groups = "wled";
};
};
sd0_pins_default: sd0-pins-default {
mux {
function = "sd";
groups = "sd_0";
};
/* "I2S2_OUT, "I2S4_IN"", "I2S3_IN", "I2S2_IN",
* "I2S4_OUT", "I2S3_OUT" are used as DAT0, DAT1,
* DAT2, DAT3, CMD, CLK for SD respectively.
*/
conf-cmd-data {
pins = "I2S2_OUT", "I2S4_IN", "I2S3_IN",
"I2S2_IN","I2S4_OUT";
input-enable;
drive-strength = <8>;
bias-pull-up;
};
conf-clk {
pins = "I2S3_OUT";
drive-strength = <12>;
bias-pull-down;
};
conf-cd {
pins = "TXD3";
bias-pull-up;
};
};
sd0_pins_uhs: sd0-pins-uhs {
mux {
function = "sd";
groups = "sd_0";
};
conf-cmd-data {
pins = "I2S2_OUT", "I2S4_IN", "I2S3_IN",
"I2S2_IN","I2S4_OUT";
input-enable;
bias-pull-up;
};
conf-clk {
pins = "I2S3_OUT";
bias-pull-down;
};
};
/* Serial NAND is shared pin with SPI-NOR */
serial_nand_pins: serial-nand-pins {
mux {
function = "flash";
groups = "snfi";
};
};
spic0_pins: spic0-pins {
mux {
function = "spi";
groups = "spic0_0";
};
};
spic1_pins: spic1-pins {
mux {
function = "spi";
groups = "spic1_0";
};
};
/* SPI-NOR is shared pin with serial NAND */
spi_nor_pins: spi-nor-pins {
mux {
function = "flash";
groups = "spi_nor";
};
};
/* serial NAND is shared pin with SPI-NOR */
serial_nand_pins: serial-nand-pins {
mux {
function = "flash";
groups = "snfi";
};
};
uart0_pins: uart0-pins {
mux {
function = "uart";
groups = "uart0_0_tx_rx" ;
};
};
uart2_pins: uart2-pins {
mux {
function = "uart";
groups = "uart2_1_tx_rx" ;
};
};
watchdog_pins: watchdog-pins {
mux {
function = "watchdog";
groups = "watchdog";
};
};
};
&pwm {
pinctrl-names = "default";
pinctrl-0 = <&pwm7_pins>;
status = "okay";
};
&pwrap {
pinctrl-names = "default";
pinctrl-0 = <&pmic_bus_pins>;
status = "okay";
};
&sata {
status = "disable";
};
&sata_phy {
status = "disable";
};
&spi0 {
pinctrl-names = "default";
pinctrl-0 = <&spic0_pins>;
status = "okay";
};
&spi1 {
pinctrl-names = "default";
pinctrl-0 = <&spic1_pins>;
status = "okay";
};
&ssusb {
vusb33-supply = <®_3p3v>;
vbus-supply = <®_5v>;
status = "okay";
};
&u3phy {
status = "okay";
};
&uart0 {
pinctrl-names = "default";
pinctrl-0 = <&uart0_pins>;
status = "okay";
};
&uart2 {
pinctrl-names = "default";
pinctrl-0 = <&uart2_pins>;
status = "okay";
};
&watchdog {
pinctrl-names = "default";
pinctrl-0 = <&watchdog_pins>;
status = "okay";
};
&wmac {
status = "okay";
};
&wmac {
status = "okay";
};Dts looks right…from your dmesg it looks like both ports are down…maybe something power-related? Can you compare your dtsi with mine (5.4-main branch except switch driver)? Have you added the other patches i’ve mentioned (irq handling, class fix)?
Looks like I found the culprit.
I just needed to apply all four patches from Spilt PCIe node to comply with hardware design series. I had to make some modifications as I mentioned above since mt7622-rfb1.dts from OpenWRT is a little bit different from what the patch is expecting (see attachments).
1002_1-dt-bindings-PCI-Mediatek-Update-PCIe-binding.patch (9.0 KB)
1002_2-mediatek-Use-regmap-to-get-shared-pcie-cfg-base.patch (2.7 KB)
1002_3-Split_PCIe_node_for_MT2712-MT7622.patch (7.9 KB)
1002_4-ARM-dts-mediatek-Update-mt7629-PCIe-node.patch (2.0 KB)
BTW is there a more elegant way of obtaining these patches rather than select - copy - paste to text editor - save as .patch - put in patches-5.4 dir?
Starting kernel ...
[ATF][ 26.267559]save kernel info
[ATF][ 26.270760]Kernel_EL2
[ATF][ 26.273516]Kernel is 64Bit
[ATF][ 26.276704]pc=0x41080000, r0=0x6bff6000, r1=0x0
INFO: BL3-1: Preparing for EL3 exit to normal world, Kernel
INFO: BL3-1: Next image address = 0x41080000
INFO: BL3-1: Next image spsr = 0x3c9
[ATF][ 26.294971]el3_exit
[ 0.000000] Booting Linux on physical CPU 0x0000000000 [0x410fd034]
[ 0.000000] Linux version 5.4.42 ([email protected]) (gcc version 8.4.0 (OpenWrt GCC 8.4.0 r13342-e35e40ad82)) #0 SMP Fri May 20
[ 0.000000] Machine model: Bananapi BPI-R64
[ 0.000000] On node 0 totalpages: 262096
[ 0.000000] DMA32 zone: 4096 pages used for memmap
[ 0.000000] DMA32 zone: 0 pages reserved
[ 0.000000] DMA32 zone: 262096 pages, LIFO batch:63
[ 0.000000] psci: probing for conduit method from DT.
[ 0.000000] psci: PSCIv0.2 detected in firmware.
[ 0.000000] psci: Using standard PSCI v0.2 function IDs
[ 0.000000] psci: Trusted OS migration not required
[ 0.000000] percpu: Embedded 20 pages/cpu s43608 r8192 d30120 u81920
[ 0.000000] pcpu-alloc: s43608 r8192 d30120 u81920 alloc=20*4096
[ 0.000000] pcpu-alloc: [0] 0 [0] 1
[ 0.000000] Detected VIPT I-cache on CPU0
[ 0.000000] CPU features: kernel page table isolation disabled by kernel configuration
[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 258000
[ 0.000000] Kernel command line: board=bpi-r64 console=ttyS0,115200n1 earlyprintk root=/dev/mmcblk0p2 rootfstype=ext4 rootwait servi2
[ 0.000000] Dentry cache hash table entries: 131072 (order: 8, 1048576 bytes, linear)
[ 0.000000] Inode-cache hash table entries: 65536 (order: 7, 524288 bytes, linear)
[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
[ 0.000000] Memory: 1018396K/1048384K available (6590K kernel code, 432K rwdata, 1896K rodata, 448K init, 285K bss, 29988K reserved,)
[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
[ 0.000000] rcu: Hierarchical RCU implementation.
[ 0.000000] rcu: CONFIG_RCU_FANOUT set to non-default value of 32.
[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 25 jiffies.
[ 0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0
[ 0.000000] GIC: GICv2 detected, but range too small and irqchip.gicv2_force_probe not set
[ 0.000000] random: get_random_bytes called from start_kernel+0x2d4/0x430 with crng_init=0
[ 0.000000] arch_timer: cp15 timer(s) running at 12.50MHz (phys).
[ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x2e2049cda, max_idle_ns: 440795202628 ns
[ 0.000003] sched_clock: 56 bits at 12MHz, resolution 80ns, wraps every 4398046511080ns
[ 0.000168] Calibrating delay loop (skipped), value calculated using timer frequency.. 25.00 BogoMIPS (lpj=50000)
[ 0.000175] pid_max: default: 32768 minimum: 301
[ 0.000260] Mount-cache hash table entries: 2048 (order: 2, 16384 bytes, linear)
[ 0.000271] Mountpoint-cache hash table entries: 2048 (order: 2, 16384 bytes, linear)
[ 0.001153] ASID allocator initialised with 65536 entries
[ 0.001203] rcu: Hierarchical SRCU implementation.
[ 0.001461] smp: Bringing up secondary CPUs ...
[ 0.001782] Detected VIPT I-cache on CPU1
[ 0.001819] CPU1: Booted secondary processor 0x0000000001 [0x410fd034]
[ 0.001873] smp: Brought up 1 node, 2 CPUs
[ 0.001880] SMP: Total of 2 processors activated.
[ 0.001884] CPU features: detected: 32-bit EL0 Support
[ 0.001888] CPU features: detected: CRC32 instructions
[ 0.001988] CPU: All CPU(s) started at EL2
[ 0.001998] alternatives: patching kernel code
[ 0.005276] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns
[ 0.005288] futex hash table entries: 512 (order: 3, 32768 bytes, linear)
[ 0.005379] pinctrl core: initialized pinctrl subsystem
[ 0.005808] NET: Registered protocol family 16
[ 0.006088] DMA: preallocated 256 KiB pool for atomic allocations
[ 0.017063] GPIO line 499 (asm_sel) hogged as output/high
[ 0.029735] SCSI subsystem initialized
[ 0.029890] libata version 3.00 loaded.
[ 0.030022] usbcore: registered new interface driver usbfs
[ 0.030052] usbcore: registered new interface driver hub
[ 0.030078] usbcore: registered new device driver usb
[ 0.030859] Bluetooth: Core ver 2.22
[ 0.030890] NET: Registered protocol family 31
[ 0.030894] Bluetooth: HCI device and connection manager initialized
[ 0.030901] Bluetooth: HCI socket layer initialized
[ 0.030908] Bluetooth: L2CAP socket layer initialized
[ 0.030919] Bluetooth: SCO socket layer initialized
[ 0.031382] clocksource: Switched to clocksource arch_sys_counter
[ 0.031850] thermal_sys: Registered thermal governor 'fair_share'
[ 0.031853] thermal_sys: Registered thermal governor 'bang_bang'
[ 0.031858] thermal_sys: Registered thermal governor 'step_wise'
[ 0.031861] thermal_sys: Registered thermal governor 'user_space'
[ 0.031865] thermal_sys: Registered thermal governor 'power_allocator'
[ 0.032119] NET: Registered protocol family 2
[ 0.032394] tcp_listen_portaddr_hash hash table entries: 512 (order: 1, 8192 bytes, linear)
[ 0.032413] TCP established hash table entries: 8192 (order: 4, 65536 bytes, linear)
[ 0.032464] TCP bind hash table entries: 8192 (order: 5, 131072 bytes, linear)
[ 0.032570] TCP: Hash tables configured (established 8192 bind 8192)
[ 0.032658] UDP hash table entries: 512 (order: 2, 16384 bytes, linear)
[ 0.032680] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes, linear)
[ 0.032770] NET: Registered protocol family 1
[ 0.032789] PCI: CLS 0 bytes, default 64
[ 0.033547] workingset: timestamp_bits=46 max_order=18 bucket_order=0
[ 0.036898] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.036909] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 0.050389] mtk-tphy 1a0c4000.usb-phy: failed to get ref_clk(id-1)
[ 0.053638] mt-pmic-pwrap 10001000.pwrap: unexpected interrupt int=0x1
[ 0.067647] Serial: 8250/16550 driver, 3 ports, IRQ sharing disabled
[ 0.068299] printk: console [ttyS0] disabled
[ 0.088649] 11002000.serial: ttyS0 at MMIO 0x11002000 (irq = 118, base_baud = 1562500) is a ST16650V2
[ 0.630082] printk: console [ttyS0] enabled
[ 0.654977] 11004000.serial: ttyS1 at MMIO 0x11004000 (irq = 119, base_baud = 1562500) is a ST16650V2
[ 0.664689] 1100c000.serial: ttyS2 at MMIO 0x1100c000 (irq = 125, base_baud = 17499995) is a MediaTek BTIF
[ 0.674422] serial serial0: tty port ttyS2 registered
[ 0.679677] cacheinfo: Unable to detect cache hierarchy for CPU 0
[ 0.687251] libphy: Fixed MDIO Bus: probed
[ 0.714662] libphy: mdio: probed
[ 0.717928] mtk_soc_eth 1b100000.ethernet: generated random MAC address c6:eb:14:54:30:ca
[ 0.726374] mtk_soc_eth 1b100000.ethernet eth0: mediatek frame engine at 0xffffffc011520000, irq 134
[ 0.735526] mtk_soc_eth 1b100000.ethernet: generated random MAC address fa:17:a9:bf:07:90
[ 0.743901] mtk_soc_eth 1b100000.ethernet eth1: mediatek frame engine at 0xffffffc011520000, irq 134
[ 0.753108] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 0.759632] ehci-pci: EHCI PCI platform driver
[ 0.764101] ehci-platform: EHCI generic platform driver
[ 0.769436] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 0.775625] ohci-platform: OHCI generic platform driver
[ 0.781397] usbcore: registered new interface driver usb-storage
[ 0.787765] rtc_mt7622 10212800.rtc: registered as rtc0
[ 0.793646] Driver for 1-wire Dallas network protocol.
[ 0.798993] mtk-thermal 1100b000.thermal: Device not calibrated, using default calibration values
[ 0.808183] mtk-wdt 10212000.watchdog: Watchdog enabled (timeout=31 sec, nowayout=0)
[ 0.816018] Bluetooth: HCI UART driver ver 2.3
[ 0.820460] Bluetooth: HCI UART protocol H4 registered
[ 0.825593] Bluetooth: HCI UART protocol BCSP registered
[ 0.830951] Bluetooth: HCI UART protocol Broadcom registered
[ 0.836628] Bluetooth: HCI UART protocol QCA registered
[ 0.867707] mtk-msdc 11240000.mmc: Got CD GPIO
[ 0.897832] NET: Registered protocol family 10
[ 0.902895] Segment Routing with IPv6
[ 0.906609] NET: Registered protocol family 17
[ 0.911072] 8021q: 802.1Q VLAN Support v1.8
[ 0.925772] mtk-pcie 1a143000.pcie: host bridge /pcie@1a143000 ranges:
[ 0.932323] mtk-pcie 1a143000.pcie: Parsing ranges property...
[ 0.938159] mtk-pcie 1a143000.pcie: MEM 0x20000000..0x27ffffff -> 0x20000000
[ 0.969503] mtk-pcie 1a143000.pcie: PCI host bridge to bus 0000:00
[ 0.975692] pci_bus 0000:00: root bus resource [bus 00-ff]
[ 0.981174] pci_bus 0000:00: root bus resource [mem 0x20000000-0x27ffffff]
[ 0.988045] pci_bus 0000:00: scanning bus
[ 0.992080] pci 0000:00:00.0: [14c3:3258] type 01 class 0x060400
[ 0.998176] pci 0000:00:00.0: reg 0x10: [mem 0x00000000-0x1ffffffff 64bit pref]
[ 1.007056] pci_bus 0000:00: fixups for bus
[ 1.011252] pci 0000:00:00.0: scanning [bus 00-00] behind bridge, pass 0
[ 1.017949] pci 0000:00:00.0: bridge configuration invalid ([bus 00-00]), reconfiguring
[ 1.025968] pci 0000:00:00.0: scanning [bus 00-00] behind bridge, pass 1
[ 1.032798] pci_bus 0000:01: scanning bus
[ 1.036937] pci 0000:01:00.0: [14c3:7615] type 00 class 0x000280
[ 1.043170] pci 0000:01:00.0: reg 0x10: [mem 0x00000000-0x000fffff 64bit]
[ 1.050887] pci 0000:01:00.0: 2.000 Gb/s available PCIe bandwidth, limited by 2.5 GT/s x1 link at 0000:00:00.0 (capable of 4.000 Gb/)
[ 1.065983] pci_bus 0000:01: fixups for bus
[ 1.070164] pci_bus 0000:01: bus scan returning with max=01
[ 1.075738] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01
[ 1.082362] pci_bus 0000:00: bus scan returning with max=01
[ 1.087946] pci 0000:00:00.0: BAR 0: no space for [mem size 0x200000000 64bit pref]
[ 1.095599] pci 0000:00:00.0: BAR 0: failed to assign [mem size 0x200000000 64bit pref]
[ 1.103599] pci 0000:00:00.0: BAR 8: assigned [mem 0x20000000-0x200fffff]
[ 1.110385] pci 0000:01:00.0: BAR 0: assigned [mem 0x20000000-0x200fffff 64bit]
[ 1.117774] pci 0000:00:00.0: PCI bridge to [bus 01]
[ 1.122751] pci 0000:00:00.0: bridge window [mem 0x20000000-0x200fffff]
[ 1.129775] mtk-pcie 1a145000.pcie: host bridge /pcie@1a145000 ranges:
[ 1.136303] mtk-pcie 1a145000.pcie: Parsing ranges property...
[ 1.142137] mtk-pcie 1a145000.pcie: MEM 0x28000000..0x2fffffff -> 0x28000000
[ 1.168099] mtk-msdc 11230000.mmc: phase: [map:fffffff] [maxlen:28] [final:9]
[ 1.176016] mmc0: new HS200 MMC card at address 0001
[ 1.182132] mmcblk0: mmc0:0001 008G30 7.28 GiB
[ 1.187577] mmcblk0boot0: mmc0:0001 008G30 partition 1 4.00 MiB
[ 1.194381] mmcblk0boot1: mmc0:0001 008G30 partition 2 4.00 MiB
[ 1.200357] mmcblk0rpmb: mmc0:0001 008G30 partition 3 4.00 MiB, chardev (250:0)
[ 1.208857] mmcblk0: p1 p2
[ 1.249492] mtk-pcie 1a145000.pcie: Port1 link down
[ 1.254486] mtk-pcie 1a145000.pcie: PCI host bridge to bus 0001:00
[ 1.260669] pci_bus 0001:00: root bus resource [bus 00-ff]
[ 1.266153] pci_bus 0001:00: root bus resource [mem 0x28000000-0x2fffffff]
[ 1.273026] pci_bus 0001:00: scanning bus
[ 1.278255] pci_bus 0001:00: fixups for bus
[ 1.282437] pci_bus 0001:00: bus scan returning with max=00
[ 1.288171] mtk_hsdma 1b007000.dma-controller: Using 3 as missing dma-requests property
[ 1.296360] mtk_hsdma 1b007000.dma-controller: MediaTek HSDMA driver registered
[ 1.859399] mt753x gsw@0: LAN/WAN VLAN setting=wllll
[ 1.864836] mt753x gsw@0: Switch is MediaTek MT7531BE rev 0
[ 6.511476] xhci-mtk 1a0c0000.usb: xHCI Host Controller
[ 6.516714] xhci-mtk 1a0c0000.usb: new USB bus registered, assigned bus number 1
[ 6.525762] xhci-mtk 1a0c0000.usb: hcc params 0x01403198 hci version 0x96 quirks 0x0000000000210010
[ 6.534833] xhci-mtk 1a0c0000.usb: irq 130, io mem 0x1a0c0000
[ 6.540976] hub 1-0:1.0: USB hub found
[ 6.544741] hub 1-0:1.0: 2 ports detected
[ 6.548978] xhci-mtk 1a0c0000.usb: xHCI Host Controller
[ 6.554208] xhci-mtk 1a0c0000.usb: new USB bus registered, assigned bus number 2
[ 6.561605] xhci-mtk 1a0c0000.usb: Host supports USB 3.0 SuperSpeed
[ 6.567899] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM.
[ 6.576205] hub 2-0:1.0: USB hub found
[ 6.579966] hub 2-0:1.0: 1 port detected
[ 6.584219] rtc_mt7622 10212800.rtc: setting system clock to 2000-01-01T00:14:21 UTC (946685661)
[ 6.599325] EXT4-fs (mmcblk0p2): mounted filesystem with ordered data mode. Opts: (null)
[ 6.607477] VFS: Mounted root (ext4 filesystem) readonly on device 179:2.
[ 6.614473] Freeing unused kernel memory: 448K
[ 6.627389] Run /sbin/init as init process
[ 6.680739] init: Console is alive
[ 6.684242] init: - watchdog -
[ 6.726757] random: fast init done
[ 6.809320] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[ 6.823175] ehci-fsl: Freescale EHCI Host controller driver
[ 6.833232] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
[ 6.841037] init: - preinit -
[ 6.922076] mtk_soc_eth 1b100000.ethernet: PPE started
[ 6.927266] mtk_soc_eth 1b100000.ethernet eth0: configuring for fixed/2500base-x link mode
[ 6.935611] mtk_soc_eth 1b100000.ethernet eth0: Link is Up - 2.5Gbps/Full - flow control rx/tx
Press the [f] key and hit [enter] to enter failsafe mode
Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
[ 10.969474] mount_root: mounting /dev/root
[ 10.975366] EXT4-fs (mmcblk0p2): re-mounted. Opts: (null)
[ 10.980936] mount_root: loading kmods from internal overlay
[ 10.994885] kmodloader: loading kernel modules from //etc/modules-boot.d/*
[ 11.002503] kmodloader: done loading kernel modules from //etc/modules-boot.d/*
[ 11.079661] urandom-seed: Seeding with /etc/urandom.seed
[ 11.093866] procd: - early -
[ 11.096801] procd: - watchdog -
[ 11.612900] procd: - watchdog -
[ 11.616159] procd: - ubus -
[ 11.623019] random: ubusd: uninitialized urandom read (4 bytes read)
[ 11.669206] random: ubusd: uninitialized urandom read (4 bytes read)
[ 11.675667] random: ubusd: uninitialized urandom read (4 bytes read)
[ 11.682285] procd: - init -
Please press Enter to activate this console.
[ 11.769213] kmodloader: loading kernel modules from /etc/modules.d/*
[ 11.773068] urngd: v1.0.2 started.
[ 11.787062] tun: Universal TUN/TAP device driver, 1.6
[ 11.802151] random: crng init done
[ 11.805573] random: 7 urandom warning(s) missed due to ratelimiting
[ 11.807487] cryptodev: driver 1.10 loaded.
[ 11.818851] i2c /dev entries driver
[ 11.829040] hidraw: raw HID events driver (C) Jiri Kosina
[ 11.836503] Mirror/redirect action on
[ 11.843855] u32 classifier
[ 11.846558] input device check on
[ 11.850241] Actions configured
[ 11.870641] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[ 11.875990] Bluetooth: BNEP filters: protocol multicast
[ 11.881222] Bluetooth: BNEP socket layer initialized
[ 11.888063] usbcore: registered new interface driver btusb
[ 11.894526] usbcore: registered new interface driver cdc_wdm
[ 11.900862] Loading modules backported from Linux version v5.7-rc3-0-g6a8b55ed4056
[ 11.908442] Backport generated by backports.git v5.7-rc3-1-0-gc0c7d2bb
[ 11.916168] Bluetooth: HIDP (Human Interface Emulation) ver 1.2
[ 11.922122] Bluetooth: HIDP socket layer initialized
[ 11.937166] Bluetooth: RFCOMM TTY layer initialized
[ 11.942077] Bluetooth: RFCOMM socket layer initialized
[ 11.947231] Bluetooth: RFCOMM ver 1.11
[ 11.952953] usbcore: registered new interface driver ums-alauda
[ 11.959517] usbcore: registered new interface driver ums-cypress
[ 11.966085] usbcore: registered new interface driver ums-datafab
[ 11.972436] usbcore: registered new interface driver ums-freecom
[ 11.978912] usbcore: registered new interface driver ums-isd200
[ 11.985152] usbcore: registered new interface driver ums-jumpshot
[ 11.991573] usbcore: registered new interface driver ums-karma
[ 11.997785] usbcore: registered new interface driver ums-sddr09
[ 12.004032] usbcore: registered new interface driver ums-sddr55
[ 12.010291] usbcore: registered new interface driver ums-usbat
[ 12.020258] wireguard: WireGuard 1.0.20200520 loaded. See www.wireguard.com for information.
[ 12.028709] wireguard: Copyright (C) 2015-2019 Jason A. Donenfeld <[email protected]>. All Rights Reserved.
[ 12.048120] xt_time: kernel timezone is -0000
[ 12.053074] usbcore: registered new interface driver cdc_ether
[ 12.096966] mt7615e 0000:01:00.0: assign IRQ: got 139
[ 12.102078] pci 0000:00:00.0: enabling device (0000 -> 0002)
[ 12.107742] pci 0000:00:00.0: enabling bus mastering
[ 12.112717] mt7615e 0000:01:00.0: enabling device (0000 -> 0002)
[ 12.118798] mt7615e 0000:01:00.0: enabling bus mastering
[ 12.125907] mt7615e 0000:01:00.0: Invalid MAC address, using random address 3e:a3:f4:1d:c7:db
[ 12.135936] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
[ 12.157301] mt7622-wmac 18000000.wmac: Invalid MAC address, using random address 6e:b2:d5:8b:f0:34
[ 12.167561] ieee80211 phy1: Selected rate control algorithm 'minstrel_ht'
[ 12.175450] mt7615e 0000:01:00.0: HW/SW Version: 0x8a108a10, Build Time: 20180518100604a
[ 12.175450]
[ 12.195206] PPP generic driver version 2.4.2
[ 12.201006] NET: Registered protocol family 24
[ 12.206635] usbcore: registered new interface driver qmi_wwan
[ 12.213157] mt7615e 0000:01:00.0: N9 Firmware Version: 2.0, Build Time: 20200131181812
[ 12.221756] mt7622-wmac 18000000.wmac: HW/SW Version: 0x8a108a10, Build Time: 20190801210006a
[ 12.221756]
[ 12.232303] kmodloader: done loading kernel modules from /etc/modules.d/*
[ 12.246908] mt7615e 0000:01:00.0: CR4 Firmware Version: _reserved_, Build Time: 20190121161307
[ 12.263510] mt7622-wmac 18000000.wmac: N9 Firmware Version: 2.0, Build Time: 20200131180931
[ 13.564852] mtk_soc_eth 1b100000.ethernet eth0: Link is Down
[ 13.573336] mtk_soc_eth 1b100000.ethernet: 0x100 = 0xffff9070, 0x10c = 0x100808ff
[ 13.580846] mtk_soc_eth 1b100000.ethernet: reset pse
[ 13.671845] mtk_soc_eth 1b100000.ethernet: PPE started
[ 13.677060] debugfs: Directory 'mtk_ppe' with parent '/' already present!
[ 13.683890] mtk_soc_eth 1b100000.ethernet eth0: configuring for fixed/2500base-x link mode
[ 13.692253] mtk_soc_eth 1b100000.ethernet eth0: Link is Up - 2.5Gbps/Full - flow control rx/tx
[ 13.698920] br-lan: port 1(eth0) entered blocking state
[ 13.706190] br-lan: port 1(eth0) entered disabled state
[ 13.711646] device eth0 entered promiscuous mode
[ 13.717901] br-lan: port 1(eth0) entered blocking state
[ 13.723176] br-lan: port 1(eth0) entered forwarding state
[ 13.736030] mtk_soc_eth 1b100000.ethernet eth1: configuring for fixed/rgmii link mode
[ 13.744068] mtk_soc_eth 1b100000.ethernet eth1: Link is Up - 1Gbps/Full - flow control rx/tx
Now I have both WiFi cards operational.
phy#1
Interface wlan1
ifindex 5
wdev 0x100000001
addr 52:43:4e:e7:4d:c6
type managed
txpower 6.00 dBm
multicast TXQ:
qsz-byt qsz-pkt flows drops marks overlmt hashcol tx-bytes tx-packets
0 0 0 0 0 0 0 0 0
phy#0
Interface wlan0
ifindex 7
wdev 0x2
addr aa:60:e3:c5:e6:f2
type managed
txpower 6.00 dBm
multicast TXQ:
qsz-byt qsz-pkt flows drops marks overlmt hashcol tx-bytes tx-packets
0 0 0 0 0 0 0 0 0
Two things bother me though.
- For some reason OpenWRT generated config files in such a way that
radio0iswlan1and vice versa. - Txpower on both cards seems to be limited to 6 dBm. Is there a way to increase it?
2 Likes