So i my have extrapolated things a bit. PLease chack if was correct.
I downloaded your files and placed:
- contents of mt7986_wifi_firmware.tar.gz in /lib/firmware/mediatek
- contents of bpi-r3-networkd/etc/systemd/network in /etc/systemd/network
- contents of bpi-r3-service/etc in /etc (merged directories and replaced files when necessary)
- contents of bpi-r3-service/lib in /lib and merged directories
After this procedure, i see 2 more interfaces but im unsure what they are:

Hostapd fails to setup on boot:

Here is the full boot log:
Starting kernel ...
[ 0.000000] Booting Linux on physical CPU 0x0000000000 [0x410fd034]
[ 0.000000] Linux version 6.1.0-bpi-r3 (joaolrc@pop-os) (aarch64-linux-gnu-gcc (Ubuntu 11.3.0-1ubuntu13
[ 0.000000] Machine model: Bananapi BPI-R3
[ 0.000000] earlycon: uart8250 at MMIO32 0x0000000011002000 (options '')
[ 0.000000] printk: bootconsole [uart8250] enabled
[ 0.000000] efi: UEFI not found.
[ 0.000000] Zone ranges:
[ 0.000000] DMA [mem 0x0000000040000000-0x00000000bfffffff]
[ 0.000000] DMA32 empty
[ 0.000000] Normal empty
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x0000000040000000-0x0000000042ffffff]
[ 0.000000] node 0: [mem 0x0000000043000000-0x000000004302ffff]
[ 0.000000] node 0: [mem 0x0000000043030000-0x000000004fbfffff]
[ 0.000000] node 0: [mem 0x000000004fc00000-0x000000004fcfffff]
[ 0.000000] node 0: [mem 0x000000004fd00000-0x00000000bfffffff]
[ 0.000000] Initmem setup node 0 [mem 0x0000000040000000-0x00000000bfffffff]
[ 0.000000] psci: probing for conduit method from DT.
[ 0.000000] psci: PSCIv1.1 detected in firmware.
[ 0.000000] psci: Using standard PSCI v0.2 function IDs
[ 0.000000] psci: MIGRATE_INFO_TYPE not supported.
[ 0.000000] psci: SMC Calling Convention v1.2
[ 0.000000] percpu: Embedded 27 pages/cpu s70952 r8192 d31448 u110592
[ 0.000000] pcpu-alloc: s70952 r8192 d31448 u110592 alloc=27*4096
[ 0.000000] pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3
[ 0.000000] Detected VIPT I-cache on CPU0
[ 0.000000] CPU features: detected: GIC system register CPU interface
[ 0.000000] CPU features: detected: ARM erratum 845719
[ 0.000000] alternatives: applying boot alternatives
[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 516096
[ 0.000000] Kernel command line: board=bpi-r3 earlycon=uart8250,mmio32,0x11002000 debug=7 root=/dev/mmt
[ 0.000000] Unknown kernel command line parameters "board=bpi-r3", will be passed to user space.
[ 0.000000] Dentry cache hash table entries: 262144 (order: 9, 2097152 bytes, linear)
[ 0.000000] Inode-cache hash table entries: 131072 (order: 8, 1048576 bytes, linear)
[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
[ 0.000000] Memory: 2029816K/2097152K available (13696K kernel code, 2644K rwdata, 4136K rodata, 4480K)
[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[ 0.000000] trace event string verifier disabled
[ 0.000000] rcu: Hierarchical RCU implementation.
[ 0.000000] rcu: RCU event tracing is enabled.
[ 0.000000] Tracing variant of Tasks RCU enabled.
[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies.
[ 0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0
[ 0.000000] GICv3: GIC: Using split EOI/Deactivate mode
[ 0.000000] GICv3: 640 SPIs implemented
[ 0.000000] GICv3: 0 Extended SPIs implemented
[ 0.000000] Root IRQ handler: gic_handle_irq
[ 0.000000] GICv3: GICv3 features: 16 PPIs
[ 0.000000] GICv3: CPU0: found redistributor 0 region 0:0x000000000c080000
[ 0.000000] rcu: srcu_init: Setting srcu_struct sizes based on contention.
[ 0.000000] arch_timer: cp15 timer(s) running at 13.00MHz (phys).
[ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x2ff89eacb, max_idle_nss
[ 0.000000] sched_clock: 56 bits at 13MHz, resolution 76ns, wraps every 4398046511101ns
[ 0.008265] Console: colour dummy device 80x25
[ 0.012729] printk: console [tty0] enabled
[ 0.016843] printk: bootconsole [uart8250] disabled
[ 0.000000] Booting Linux on physical CPU 0x0000000000 [0x410fd034]
[ 0.000000] Linux version 6.1.0-bpi-r3 (joaolrc@pop-os) (aarch64-linux-gnu-gcc (Ubuntu 11.3.0-1ubuntu13
[ 0.000000] Machine model: Bananapi BPI-R3
[ 0.000000] earlycon: uart8250 at MMIO32 0x0000000011002000 (options '')
[ 0.000000] printk: bootconsole [uart8250] enabled
[ 0.000000] efi: UEFI not found.
[ 0.000000] Zone ranges:
[ 0.000000] DMA [mem 0x0000000040000000-0x00000000bfffffff]
[ 0.000000] DMA32 empty
[ 0.000000] Normal empty
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x0000000040000000-0x0000000042ffffff]
[ 0.000000] node 0: [mem 0x0000000043000000-0x000000004302ffff]
[ 0.000000] node 0: [mem 0x0000000043030000-0x000000004fbfffff]
[ 0.000000] node 0: [mem 0x000000004fc00000-0x000000004fcfffff]
[ 0.000000] node 0: [mem 0x000000004fd00000-0x00000000bfffffff]
[ 0.000000] Initmem setup node 0 [mem 0x0000000040000000-0x00000000bfffffff]
[ 0.000000] psci: probing for conduit method from DT.
[ 0.000000] psci: PSCIv1.1 detected in firmware.
[ 0.000000] psci: Using standard PSCI v0.2 function IDs
[ 0.000000] psci: MIGRATE_INFO_TYPE not supported.
[ 0.000000] psci: SMC Calling Convention v1.2
[ 0.000000] percpu: Embedded 27 pages/cpu s70952 r8192 d31448 u110592
[ 0.000000] pcpu-alloc: s70952 r8192 d31448 u110592 alloc=27*4096
[ 0.000000] pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3
[ 0.000000] Detected VIPT I-cache on CPU0
[ 0.000000] CPU features: detected: GIC system register CPU interface
[ 0.000000] CPU features: detected: ARM erratum 845719
[ 0.000000] alternatives: applying boot alternatives
[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 516096
[ 0.000000] Kernel command line: board=bpi-r3 earlycon=uart8250,mmio32,0x11002000 debug=7 root=/dev/mmt
[ 0.000000] Unknown kernel command line parameters "board=bpi-r3", will be passed to user space.
[ 0.000000] Dentry cache hash table entries: 262144 (order: 9, 2097152 bytes, linear)
[ 0.000000] Inode-cache hash table entries: 131072 (order: 8, 1048576 bytes, linear)
[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
[ 0.000000] Memory: 2029816K/2097152K available (13696K kernel code, 2644K rwdata, 4136K rodata, 4480K)
[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[ 0.000000] trace event string verifier disabled
[ 0.000000] rcu: Hierarchical RCU implementation.
[ 0.000000] rcu: RCU event tracing is enabled.
[ 0.000000] Tracing variant of Tasks RCU enabled.
[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies.
[ 0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0
[ 0.000000] GICv3: GIC: Using split EOI/Deactivate mode
[ 0.000000] GICv3: 640 SPIs implemented
[ 0.000000] GICv3: 0 Extended SPIs implemented
[ 0.000000] Root IRQ handler: gic_handle_irq
[ 0.000000] GICv3: GICv3 features: 16 PPIs
[ 0.000000] GICv3: CPU0: found redistributor 0 region 0:0x000000000c080000
[ 0.000000] rcu: srcu_init: Setting srcu_struct sizes based on contention.
[ 0.000000] arch_timer: cp15 timer(s) running at 13.00MHz (phys).
[ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x2ff89eacb, max_idle_nss
[ 0.000000] sched_clock: 56 bits at 13MHz, resolution 76ns, wraps every 4398046511101ns
[ 0.008265] Console: colour dummy device 80x25
[ 0.012729] printk: console [tty0] enabled
[ 0.016843] printk: bootconsole [uart8250] disabled
[ 0.021769] Calibrating delay loop (skipped), value calculated using timer frequency.. 26.00 BogoMIPS )
[ 0.021780] pid_max: default: 32768 minimum: 301
[ 0.021870] Mount-cache hash table entries: 4096 (order: 3, 32768 bytes, linear)
[ 0.021886] Mountpoint-cache hash table entries: 4096 (order: 3, 32768 bytes, linear)
[ 0.022476] cacheinfo: Unable to detect cache hierarchy for CPU 0
[ 0.022771] cblist_init_generic: Setting adjustable number of callback queues.
[ 0.022783] cblist_init_generic: Setting shift to 2 and lim to 1.
[ 0.022883] rcu: Hierarchical SRCU implementation.
[ 0.022889] rcu: Max phase no-delay instances is 1000.
[ 0.023334] EFI services will not be available.
[ 0.023494] smp: Bringing up secondary CPUs ...
[ 0.023815] Detected VIPT I-cache on CPU1
[ 0.023866] cacheinfo: Unable to detect cache hierarchy for CPU 1
[ 0.023875] GICv3: CPU1: found redistributor 1 region 0:0x000000000c0a0000
[ 0.023906] CPU1: Booted secondary processor 0x0000000001 [0x410fd034]
[ 0.024234] Detected VIPT I-cache on CPU2
[ 0.024268] cacheinfo: Unable to detect cache hierarchy for CPU 2
[ 0.024272] GICv3: CPU2: found redistributor 2 region 0:0x000000000c0c0000
[ 0.024285] CPU2: Booted secondary processor 0x0000000002 [0x410fd034]
[ 0.024553] Detected VIPT I-cache on CPU3
[ 0.024581] cacheinfo: Unable to detect cache hierarchy for CPU 3
[ 0.024586] GICv3: CPU3: found redistributor 3 region 0:0x000000000c0e0000
[ 0.024597] CPU3: Booted secondary processor 0x0000000003 [0x410fd034]
[ 0.024628] smp: Brought up 1 node, 4 CPUs
[ 0.024678] SMP: Total of 4 processors activated.
[ 0.024684] CPU features: detected: 32-bit EL0 Support
[ 0.024691] CPU features: detected: CRC32 instructions
[ 0.024734] CPU features: emulated: Privileged Access Never (PAN) using TTBR0_EL1 switching
[ 0.024745] CPU: All CPU(s) started at EL2
[ 0.024750] alternatives: applying system-wide alternatives
[ 0.026103] devtmpfs: initialized
[ 0.028043] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750s
[ 0.028074] futex hash table entries: 1024 (order: 4, 65536 bytes, linear)
[ 0.028180] pinctrl core: initialized pinctrl subsystem
[ 0.028470] DMI not present or invalid.
[ 0.028820] NET: Registered PF_NETLINK/PF_ROUTE protocol family
[ 0.029116] DMA: preallocated 256 KiB GFP_KERNEL pool for atomic allocations
[ 0.029153] DMA: preallocated 256 KiB GFP_KERNEL|GFP_DMA pool for atomic allocations
[ 0.029185] DMA: preallocated 256 KiB GFP_KERNEL|GFP_DMA32 pool for atomic allocations
[ 0.029568] thermal_sys: Registered thermal governor 'fair_share'
[ 0.029571] thermal_sys: Registered thermal governor 'bang_bang'
[ 0.029578] thermal_sys: Registered thermal governor 'step_wise'
[ 0.029584] thermal_sys: Registered thermal governor 'user_space'
[ 0.029674] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers.
[ 0.029735] ASID allocator initialised with 65536 entries
[ 0.041160] cryptd: max_cpu_qlen set to 1000
[ 0.042091] iommu: Default domain type: Translated
[ 0.042114] iommu: DMA domain TLB invalidation policy: strict mode
[ 0.042240] SCSI subsystem initialized
[ 0.042354] libata version 3.00 loaded.
[ 0.042445] usbcore: registered new interface driver usbfs
[ 0.042470] usbcore: registered new interface driver hub
[ 0.042492] usbcore: registered new device driver usb
[ 0.042735] i2c-gpio i2c-gpio-0: using lines 427 (SDA) and 428 (SCL)
[ 0.042846] i2c-gpio i2c-gpio-1: using lines 429 (SDA) and 430 (SCL)
[ 0.042886] pps_core: LinuxPPS API ver. 1 registered
[ 0.042892] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <[email protected]>
[ 0.042906] PTP clock support registered
[ 0.043715] vgaarb: loaded
[ 0.522370] clocksource: Switched to clocksource arch_sys_counter
[ 0.526528] NET: Registered PF_INET protocol family
[ 0.526735] IP idents hash table entries: 32768 (order: 6, 262144 bytes, linear)
[ 0.527875] tcp_listen_portaddr_hash hash table entries: 1024 (order: 2, 16384 bytes, linear)
[ 0.527928] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear)
[ 0.527944] TCP established hash table entries: 16384 (order: 5, 131072 bytes, linear)
[ 0.528021] TCP bind hash table entries: 16384 (order: 7, 524288 bytes, linear)
[ 0.528431] TCP: Hash tables configured (established 16384 bind 16384)
[ 0.528549] UDP hash table entries: 1024 (order: 3, 32768 bytes, linear)
[ 0.528597] UDP-Lite hash table entries: 1024 (order: 3, 32768 bytes, linear)
[ 0.528779] NET: Registered PF_UNIX/PF_LOCAL protocol family
[ 0.529189] RPC: Registered named UNIX socket transport module.
[ 0.529205] RPC: Registered udp transport module.
[ 0.529210] RPC: Registered tcp transport module.
[ 0.529216] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 0.529797] PCI: CLS 0 bytes, default 64
[ 0.547080] Initialise system trusted keyrings
[ 0.547248] workingset: timestamp_bits=46 max_order=19 bucket_order=0
[ 0.550191] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.551065] NFS: Registering the id_resolver key type
[ 0.551104] Key type id_resolver registered
[ 0.551110] Key type id_legacy registered
[ 0.551154] nfs4filelayout_init: NFSv4 File Layout Driver Registering...
[ 0.551162] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering...
[ 0.551550] Key type cifs.idmap registered
[ 0.551562] jffs2: version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc.
[ 0.551753] fuse: init (API version 7.37)
[ 0.573437] Key type asymmetric registered
[ 0.573455] Asymmetric key parser 'x509' registered
[ 0.573499] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 248)
[ 0.573509] io scheduler mq-deadline registered
[ 0.573517] io scheduler kyber registered
[ 0.607410] Serial: 8250/16550 driver, 3 ports, IRQ sharing disabled
[ 0.628939] 11002000.serial: ttyS0 at MMIO 0x11002000 (irq = 116, base_baud = 2500000) is a ST16650V2
[ 1.510300] printk: console [ttyS0] enabled
[ 1.535545] 11003000.serial: ttyS1 at MMIO 0x11003000 (irq = 117, base_baud = 1625000) is a ST16650V2
[ 1.565728] 11004000.serial: ttyS2 at MMIO 0x11004000 (irq = 118, base_baud = 1625000) is a ST16650V2
[ 1.575688] mtk_rng 1020f000.rng: registered RNG driver
[ 1.581166] cacheinfo: Unable to detect cache hierarchy for CPU 0
[ 1.590595] loop: module loaded
[ 1.595421] spi-nand spi0.0: Winbond SPI NAND was found.
[ 1.600743] spi-nand spi0.0: 128 MiB, block size: 128 KiB, page size: 2048, OOB size: 64
[ 1.609045] 4 fixed-partitions partitions found on MTD device spi0.0
[ 1.615400] Creating 4 MTD partitions on "spi0.0":
[ 1.620179] 0x000000580000-0x000008000000 : "ubi"
[ 1.740209] 0x000000380000-0x000000580000 : "fip"
[ 1.747717] 0x000000080000-0x000000380000 : "reserved"
[ 1.756553] 0x000000000000-0x000000080000 : "bl2"
[ 1.763636] sfp sfp-1: Host maximum power 1.0W
[ 1.768580] sfp sfp-2: Host maximum power 1.0W
[ 1.787345] mtk_soc_eth 15100000.ethernet eth0: mediatek frame engine at 0xffffffc00b100000, irq 121
[ 1.796563] mtk_soc_eth 15100000.ethernet: generated random MAC address ae:6d:42:4e:60:4d
[ 1.804988] mtk_soc_eth 15100000.ethernet eth1: mediatek frame engine at 0xffffffc00b100000, irq 121
[ 1.814531] usbcore: registered new interface driver usb-storage
[ 1.820722] i2c_dev: i2c /dev entries driver
[ 1.827044] mtk-wdt 1001c000.watchdog: Watchdog enabled (timeout=31 sec, nowayout=0)
[ 1.835750] SMCCC: SOC_ID: ID = jep106:0426:7986 Revision = 0x00000000
[ 1.842436] usbcore: registered new interface driver usbhid
[ 1.848015] usbhid: USB HID core driver
[ 1.852186] NET: Registered PF_INET6 protocol family
[ 1.857929] Segment Routing with IPv6
[ 1.861615] In-situ OAM (IOAM) with IPv6
[ 1.865605] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver
[ 1.871899] NET: Registered PF_PACKET protocol family
[ 1.877107] 8021q: 802.1Q VLAN Support v1.8
[ 1.881314] Key type dns_resolver registered
[ 1.886032] Loading compiled-in X.509 certificates
[ 1.896725] mmc0: host does not support reading read-only switch, assuming write-enable
[ 1.899494] mtk-pcie-gen3 11280000.pcie: host bridge /soc/pcie@11280000 ranges:
[ 1.908062] mmc0: new high speed SDHC card at address aaaa
[ 1.912052] mtk-pcie-gen3 11280000.pcie: Parsing ranges property...
[ 1.918322] mmcblk0: mmc0:aaaa SR32G 29.7 GiB
[ 1.923781] mtk-pcie-gen3 11280000.pcie: MEM 0x0020000000..0x002fffffff -> 0x0020000000
[ 1.932856] GPT:Primary header thinks Alt. header is not at the end of the disk.
[ 1.944053] GPT:1 != 62333951
[ 1.947011] GPT:Alternate GPT header not at the end of the disk.
[ 1.953008] GPT:1 != 62333951
[ 1.955962] GPT: Use GNU Parted to correct GPT errors.
[ 1.961100] mmcblk0: p1 p2 p3 p4 p5 p6
[ 2.152372] mtk-pcie-gen3 11280000.pcie: PCIe link down, current LTSSM state: detect.active (0x1000001)
[ 2.161798] mtk-pcie-gen3: probe of 11280000.pcie failed with error -110
[ 2.191290] mt7530 mdio-bus:1f: configuring for fixed/2500base-x link mode
[ 2.198460] mt7530 mdio-bus:1f: Link is Up - 2.5Gbps/Full - flow control rx/tx
[ 2.207403] mt7530 mdio-bus:1f wan (uninitialized): PHY [mt7530-0:00] driver [MediaTek MT7531 PHY] (ir)
[ 2.227280] mt7530 mdio-bus:1f lan0 (uninitialized): PHY [mt7530-0:01] driver [MediaTek MT7531 PHY] (i)
[ 2.246956] mt7530 mdio-bus:1f lan1 (uninitialized): PHY [mt7530-0:02] driver [MediaTek MT7531 PHY] (i)
[ 2.266618] mt7530 mdio-bus:1f lan2 (uninitialized): PHY [mt7530-0:03] driver [MediaTek MT7531 PHY] (i)
[ 2.286286] mt7530 mdio-bus:1f lan3 (uninitialized): PHY [mt7530-0:04] driver [MediaTek MT7531 PHY] (i)
[ 2.297226] device eth0 entered promiscuous mode
[ 2.301881] DSA: tree 0 setup
[ 2.305248] xhci-mtk 11200000.usb: supply vbus not found, using dummy regulator
[ 2.312639] xhci-mtk 11200000.usb: supply vusb33 not found, using dummy regulator
[ 2.320982] xhci-mtk 11200000.usb: xHCI Host Controller
[ 2.326225] xhci-mtk 11200000.usb: new USB bus registered, assigned bus number 1
[ 2.336609] xhci-mtk 11200000.usb: hcc params 0x01403f99 hci version 0x110 quirks 0x0000000000210010
[ 2.345772] xhci-mtk 11200000.usb: irq 132, io mem 0x11200000
[ 2.351590] xhci-mtk 11200000.usb: xHCI Host Controller
[ 2.356812] xhci-mtk 11200000.usb: new USB bus registered, assigned bus number 2
[ 2.364200] xhci-mtk 11200000.usb: Host supports USB 3.2 Enhanced SuperSpeed
[ 2.371696] hub 1-0:1.0: USB hub found
[ 2.375475] hub 1-0:1.0: 2 ports detected
[ 2.379771] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM.
[ 2.388207] hub 2-0:1.0: USB hub found
[ 2.391970] hub 2-0:1.0: 1 port detected
[ 2.396988] cfg80211: Loading compiled-in X.509 certificates for regulatory database
[ 2.405645] cfg80211: Loaded X.509 cert 'sforshee: 00b28ddf47aef9cea7'
[ 2.412735] platform regulatory.0: Direct firmware load for regulatory.db failed with error -2
[ 2.421339] platform regulatory.0: Falling back to sysfs fallback for: regulatory.db
[ 2.439832] EXT4-fs (mmcblk0p6): INFO: recovery required on readonly filesystem
[ 2.447159] EXT4-fs (mmcblk0p6): write access will be enabled during recovery
[ 2.842355] usb 1-1: new high-speed USB device number 2 using xhci-mtk
[ 3.023115] hub 1-1:1.0: USB hub found
[ 3.026919] hub 1-1:1.0: 4 ports detected
[ 3.099877] EXT4-fs (mmcblk0p6): recovery complete
[ 3.109339] EXT4-fs (mmcblk0p6): mounted filesystem with ordered data mode. Quota mode: disabled.
[ 3.118240] VFS: Mounted root (ext4 filesystem) readonly on device 179:6.
[ 3.126070] devtmpfs: mounted
[ 3.130574] Freeing unused kernel memory: 4480K
[ 3.135195] Run /sbin/init as init process
[ 3.139278] with arguments:
[ 3.142233] /sbin/init
[ 3.144933] with environment:
[ 3.148060] HOME=/
[ 3.150407] TERM=linux
[ 3.153107] board=bpi-r3
[ 3.799001] systemd[1]: System time before build time, advancing clock.
[ 3.825626] systemd[1]: Failed to look up module alias 'autofs4': Function not implemented
[ 3.868705] systemd[1]: systemd 247.3-7+deb11u1 running in system mode. (+PAM +AUDIT +SELINUX +IMA +AP)
[ 3.891991] systemd[1]: Detected architecture arm64.
Welcome to Debian GNU/Linux 11 (bullseye)!
[ 3.943229] systemd[1]: Set hostname to <bpi-r3>.
[ 4.593203] systemd[1]: /etc/systemd/system/rc-local.service:11: Support for option SysVStartPriority=d
[ 4.628493] systemd[1]: Queued start job for default target Graphical Interface.
[ 11.992615] random: crng init done
[ 11.992759] systemd[1]: system-getty.slice: unit configures an IP firewall, but the local system does .
[ 12.008361] systemd[1]: (This warning is only shown for the first unit using IP firewalling.)
[ 12.053407] systemd[1]: Created slice system-getty.slice.
[ OK ] Created slice system-getty.slice.
[ 12.093234] systemd[1]: Created slice system-modprobe.slice.
[ OK ] Created slice system-modprobe.slice.
[ 12.133167] systemd[1]: Created slice system-serial\x2dgetty.slice.
[ OK ] Created slice system-serial\x2dgetty.slice.
[ 12.173054] systemd[1]: Created slice User and Session Slice.
[ OK ] Created slice User and Session Slice.
[ 12.212670] systemd[1]: Started Dispatch Password Requests to Console Directory Watch.
[ OK ] Started Dispatch Password …ts to Console Directory Watch.
[ 12.252565] systemd[1]: Started Forward Password Requests to Wall Directory Watch.
[ OK ] Started Forward Password R…uests to Wall Directory Watch.
[ 12.292511] systemd[1]: Condition check resulted in Arbitrary Executable File Formats File System Auto.
[ 12.304197] systemd[1]: Reached target Local Encrypted Volumes.
[ OK ] Reached target Local Encrypted Volumes.
[ 12.342512] systemd[1]: Reached target Paths.
[ OK ] Reached target Paths.
[ 12.372432] systemd[1]: Reached target Remote File Systems.
[ OK ] Reached target Remote File Systems.
[ 12.412421] systemd[1]: Reached target Slices.
[ OK ] Reached target Slices.
[ 12.442440] systemd[1]: Reached target Swap.
[ OK ] Reached target Swap.
[ 12.472845] systemd[1]: Listening on Syslog Socket.
[ OK ] Listening on Syslog Socket.
[ 12.502651] systemd[1]: Listening on initctl Compatibility Named Pipe.
[ OK ] Listening on initctl Compatibility Named Pipe.
[ 12.547219] systemd[1]: Condition check resulted in Journal Audit Socket being skipped.
[ 12.555746] systemd[1]: Listening on Journal Socket (/dev/log).
[ OK ] Listening on Journal Socket (/dev/log).
[ 12.592855] systemd[1]: Listening on Journal Socket.
[ OK ] Listening on Journal Socket.
[ 12.622927] systemd[1]: Listening on Network Service Netlink Socket.
[ OK ] Listening on Network Service Netlink Socket.
[ 12.663662] systemd[1]: Listening on udev Control Socket.
[ OK ] Listening on udev Control Socket.
[ 12.702760] systemd[1]: Listening on udev Kernel Socket.
[ OK ] Listening on udev Kernel Socket.
[ 12.742750] systemd[1]: Condition check resulted in Huge Pages File System being skipped.
[ 12.822594] systemd[1]: Mounting POSIX Message Queue File System...
Mounting POSIX Message Queue File System...
[ 12.864724] systemd[1]: Mounting Kernel Debug File System...
Mounting Kernel Debug File System...
[ 12.904761] systemd[1]: Mounting Kernel Trace File System...
Mounting Kernel Trace File System...
[ 12.942626] systemd[1]: Condition check resulted in Create list of static device nodes for the current.
[ 12.956323] systemd[1]: Starting Load Kernel Module configfs...
Starting Load Kernel Module configfs...
[ 12.994915] systemd[1]: Starting Load Kernel Module drm...
Starting Load Kernel Module drm...
[ 13.034874] systemd[1]: Starting Load Kernel Module fuse...
Starting Load Kernel Module fuse...
[ 13.072538] systemd[1]: Condition check resulted in OpenVSwitch configuration for cleanup being skippe.
[ 13.083679] systemd[1]: Condition check resulted in Set Up Additional Binary Formats being skipped.
[ 13.132836] systemd[1]: Starting Journal Service...
Starting Journal Service...
[ 13.167300] systemd[1]: Starting Load Kernel Modules...
Starting Load Kernel Modules...
[ 13.204843] systemd[1]: Starting Remount Root and Kernel File Systems...
Starting Remount Root and Kernel File Systems...
[ 13.228536] EXT4-fs (mmcblk0p6): re-mounted. Quota mode: disabled.
[ 13.244856] systemd[1]: Starting Coldplug All udev Devices...
Starting Coldplug All udev Devices...
[ 13.286379] systemd[1]: Started Journal Service.
[ OK ] Started Journal Service.
[ OK ] Mounted POSIX Message Queue File System.
[ OK ] Mounted Kernel Debug File System.
[ OK ] Mounted Kernel Trace File System.
[ OK ] Finished Load Kernel Module configfs.
[ OK ] Finished Load Kernel Module drm.
[ OK ] Finished Load Kernel Module fuse.
[FAILED] Failed to start Load Kernel Modules.
See 'systemctl status systemd-modules-load.service' for details.
[ OK ] Finished Remount Root and Kernel File Systems.
Mounting FUSE Control File System...
Mounting Kernel Configuration File System...
Starting Flush Journal to Persistent Storage...
[ 13.757131] systemd-journald[1102]: Received client request to flush runtime journal.
Starting Load/Save Random Seed...
[ 13.797646] systemd-journald[1102]: File /var/log/journal/f223b6b9f19a4af09caff671d8e9d1c1/system.jour.
Starting Apply Kernel Variables...
Starting Create System Users...
[ OK ] Mounted FUSE Control File System.
[ OK ] Finished Coldplug All udev Devices.
[ OK ] Mounted Kernel Configuration File System.
Starting Helper to synchronize boot up for ifupdown...
[ OK ] Finished Load/Save Random Seed.
[ OK ] Finished Apply Kernel Variables.
[ OK ] Finished Create System Users.
[ OK ] Finished Flush Journal to Persistent Storage.
Starting Create Static Device Nodes in /dev...
[ OK ] Finished Create Static Device Nodes in /dev.
[ OK ] Reached target Local File Systems (Pre).
Starting Rule-based Manage…for Device Events and Files...
[ OK ] Started Rule-based Manager for Device Events and Files.
Starting Network Service...
[ 14.595141] mtdblock: MTD device 'ubi' is NAND, please consider using UBI block devices instead.
[ OK 14.604678] mtdblock: MTD device 'fip' is NAND, please consider using UBI block devices instead.
0m] Found device[ 14.609329] mtdblock: MTD device 'reserved' is NAND, please consider using UBI block d.
/dev/t[ 14.625409] mtdblock: MTD device 'bl2' is NAND, please consider using UBI block devices instead.
[ 14.627772] cfg80211: failed to load regulatory.db
tyS0.
[ OK ] Found device /dev/mmcblk0p5.
[ OK ] Finished Helper to synchronize boot up for ifupdown.
[ 15.249101] mtk_soc_eth 15100000.ethernet eth0: configuring for fixed/2500base-x link mode
[ 15.257451] mtk_soc_eth 15100000.ethernet eth0: Link is Up - 2.5Gbps/Full - flow control rx/tx
[ 15.258130] mt7530 mdio-bus:1f lan3: configuring for phy/gmii link mode
[ OK ] Started 15.274849] mt7530 mdio-bus:1f lan2: configuring for phy/gmii link mode
1;39mNetwork Service.
[ 15.283888] lanbr0: port 1(lan1) entered blocking state
[ 15.289967] lanbr0: port 1(lan1) entered disabled state
[ 15.298473] device lan1 entered promiscuous mode
[ 15.306261] lanbr0: port 2(lan0) entered blocking state
[ 15.311495] lanbr0: port 2(lan0) entered disabled state
[ 15.318260] device lan0 entered promiscuous mode
[ 15.393647] mt7530 mdio-bus:1f wan: configuring for phy/gmii link mode
[ 15.400697] device wan entered promiscuous mode
[ 15.553381] mt7530 mdio-bus:1f lan1: configuring for phy/gmii link mode
[ 15.561318] mt7530 mdio-bus:1f lan0: configuring for phy/gmii link mode
[ OK ] Listening on Load/Save RF …itch Status /dev/rfkill Watch.
Mounting /boot...
[ 15.776774] FAT-fs (mmcblk0p5): Volume was not properly unmounted. Some data may be corrupt. Please ru.
[ OK ] Mounted /boot.
[ OK ] Reached target Local File Systems.
[ OK ] Started ifup for lan2.
Starting Raise network interfaces...
Starting Create Volatile Files and Directories...
[ OK ] Finished Create Volatile Files and Directories.
Starting Network Name Resolution...
Starting Update UTMP about System Boot/Shutdown...
[ OK ] Finished Raise network interfaces.
[ OK ] Finished Update UTMP about System Boot/Shutdown.
[ OK ] Reached target System Initialization.
[ OK ] Started Daily apt download activities.
[ OK ] Started Daily apt upgrade and clean activities.
[ OK ] Started Periodic ext4 Onli…ata Check for All Filesystems.
[ OK ] Started Discard unused blocks once a week.
[ OK ] Started Daily rotation of log files.
[ OK ] Started Daily Cleanup of Temporary Directories.
[ OK ] Reached target Timers.
[ OK ] Listening on D-Bus System Message Bus Socket.
[ OK ] Reached target Sockets.
[ OK ] Reached target Basic System.
[ OK ] Started Regular background program processing daemon.
[ OK ] Started D-Bus System Message Bus.
Starting Remove Stale Onli…t4 Metadata Check Snapshots...
Starting /etc/rc.local...
Starting System Logging Service...
Starting User Login Management...
[ OK ] Started TagProbeFirmware startup.
[ OK ] Started Network Name Resolution.
[ OK ] Started /etc/rc.local.
[ OK ] Reached target Network.
Starting dnsmasq - A light…DHCP and caching DNS server...
Starting Access point and …rver for Wi-Fi and Ethernet...
Starting OpenBSD Secure Shell server...
Starting Permit User Sessions...
[ OK ] Finished Permit User Sessions.
[ OK ] Started User Login Management.
[ OK ] Started Getty on tty1.
[ OK ] Started Serial Getty on ttyS0.
[ OK ] Reached target Login Prompts.
[FAILED] Failed to start Access poi…server for Wi-Fi and Ethernet.
See 'systemctl status hostapd.service' for details.
[ OK ] Started dnsmasq - A lightw…t DHCP and caching DNS server.
[ OK ] Reached target Host and Network Name Lookups.
[ OK ] Started OpenBSD Secure Shell server.
[ OK ] Finished Remove Stale Onli…ext4 Metadata Check Snapshots.
[ OK ] Stopped Access point and a…server for Wi-Fi and Ethernet.
Starting Access point and …rver for Wi-Fi and Ethernet...
[FAILED] Failed to start Access poi…server for Wi-Fi and Ethernet.
See 'systemctl status hostapd.service' for details.
[ OK ] Stopped Access point and a…server for Wi-Fi and Ethernet.
Starting Access point and …rver for Wi-Fi and Ethernet...
[FAILED] Failed to start Access poi…server for Wi-Fi and Ethernet.
See 'systemctl status hostapd.service' for details.
Debian GNU/Linux 11 bpi-r3 ttyS0