Bananan BPI-R4 + Compatible Fiber Optic Module with ISP Provider

[mcd007]

The question is simple for those with knowledge: which module is compatible with the BPI-R4 that can replace the ONU provided by the ISP?

From what I understand, the XPON module would be ideal, with an embedded web interface, similar to the provider’s ONU. For my provider, the ideal would be with an SC APC port.

What else do I need to consider to make it work?

Below is the ONU equipment I want to replace with an XPON stick module: Modelo: Onu Cianet Gb01

Possible replacement model:

https://pt.aliexpress.com/item/1005003515662920.html

[Thanks]

Read this thread and all your questions will be answered:

[BPI-R4] and SFP

For more info from kernel, do this before inserting sfp: echo "file drivers/net/phy/* +p" > /sys/kernel/debug/dynamic_debug/control Hopefully dynamic debugging is enabled… Then it shows more on how mac is configured… 1000Mbps sgmii leave autoneg on. It is only broken for 2500base-x. Disabling it may break it.

[KFO (MJZ)]

@Thanks Thank you for sharing the link … I read it and again I confused … Because there many of msg mixing… my mind memory is 2 RAM so Simple thing direct to point will be easy for me and for other users …

Note: I saw your post about Huawei and Nokia parts for pon … Like other device place of ISP router

@mcd007 Thank you man for creating this subject… This subject will increase our knowledge and support us to know the right items to be selected

Router From Fiber provider (ISP)

My plan to use GPON or XPON directly to BPI-R4 https://pt.aliexpress.com/item/1005003515662920.html

[Thanks]

@KFO

Simple thing direct to point

There are few xPON ONU SFP Sticks and only a few are recommended:

• [BPI-R4] and SFP - #114 by Thanks
• Anime4000/RTL960x: GPON ONU SFP Stick to suite your ISP Fiber

Buy any SFP device either RJ45, Optical or xPON ONU Stick listed here, because it means that it is supported in the linux kernel (and OpenWrt) and works without problems on Banana Pi BPI-R3 / BPI-R4, do not buy clones, only genuine / original devices:

• linux/drivers/net/phy/sfp.c

Like these xPON ONU SFP Sticks:

• Huawei MA5671A and Nokia G-010S-P.
• They need to be rooted and flashed with OpenWrt firmware.

Use Google or YouTube to find out what data you need to get from the ISP optical modem and how to configure the xPON ONU SFP Stick:

• Stock ONU - OMCI Information
• Eliminar ou trocar ONU/ONT/HGU da operadora/provedor

Example:

1. ISP Optical Modem Information:

Device Information
******************
Vendor ID:           HWTC
GPON Serial Number:  HWTCFC7DF38D
Hardware Version:    18AD.A
Software Version:    V7R0405103112
MAC Address:         00:01:02:03:04:05
SLID Password:       12345 or leave blank if the ISP does not use SLID password


VLAN Internet
*************
VLAN ID:           7
Priority:          1
Username (PPPoE):  Used in ISP optical modem
Password (PPPoE):  Used in ISP optical modem

VLAN VoIP
*********
VLAN ID:   3
Priority:  4

VLAN IPTV
*********
VLAN ID:   2
Priority:  3


VoIP (SIP) Information
**********************
Active Outbound Proxy:   Used in ISP optical modem
Outbound Proxy Address:  Used in ISP optical modem
Outbound Proxy Port:     5070

Registrar Server Address:  Used in ISP optical modem
Registrar Server Port:     5060

SIP Client Auth Username:  Used in ISP optical modem
SIP Client Auth Password:  Used in ISP optical modem

2. Configure Huawei MA5671A and Nokia G-010S-P (already rooted and flashed with OpenWrt firmware):

GPON -> General Settings
========================

Basic Settings
**************
GPON SN (GPON Serial Number):    HWTCFC7DF38D
PLOAM Password (SLID Password):

VLAN
****
Interoperability mode:         Enabled
Default PVID (VLAN Internet):  7

Advanced Settings
*****************
Custom MIB configuration files:            Enabled
Vendor ID (First four digits of GPON SN):  HWTC
Equipment ID (GPON SN):                    HWTCFC7DF38D
ONT version (Hardware Version):            18AD.A

Custom OMCID version:              Enabled
OMCID version (Software Version):  V7R0405103112

Disable RX Loss Status:  Enabled
Ignore RX loss:          Enabled


GPON -> IP/MAC Settings
=======================
HOST interface (WAN) MAC address (ISP Modem MAC Address):  00:01:02:03:04:05

LTC interface (LAN) IP address:  192.168.1.10  (Do not change this)


Commands via SSH Terminal
=========================
fw_setenv image0_version V7R0405103112

fw_setenv image1_version V7R0405103112

fw_setenv omci_version V7R0405103112

fw_printenv

3. Change the IP address “192.168.1.1” of the LAN interface on the Banana Pi BPI-R3 / BPI-R4 router to any other (example: 192.168.5.1), add VLAN for internet and the SFP WAN interface, either regular or PPPoE (credentials used in the ISP optical modem) and do this:

• [OpenWrt Wiki] Accessing the modem through the router

Follow these steps:

@phuongnam

I wrote this notice to contribute to the community (for those who are having problems filming PPPoE). I have dialed PPPoE on SFP WAN port or WAN port successfully. The equipment I use includes Converter Juplink 2.5G and SPF module G-010S-P (Alcatel Lucent)

Noted:

• For my area, it is necessary to set up GPON S/N (on the ISP modem) on the SFP module and tag VLAN 35
• pay attention to the port and device naming which can cause confusion (I don’t know why the company leaves it like that) The SFP WAN port on the left is eth2, the other port on the right is SFP LAN is eth1, next is the WAN ethernet port, and 3 LAN ports. You can see it grouped under network → interface → device

Method 1 using Converter Juplink + SFP:

• Plug optical SFP into Convert
• Plug the ethernet cable into the computer, set up static ip for the computer as 192.168.1.11/24
• Access 192.168.1.10 (SFP’s default IP) on the browser and click login username/password (root/empty)
• Go to GPON option 1 tab, enter GPON S/N on the ISP modem located behind the modem => save and apply => reboot
• Unplug the cable on the computer and plug it into the WAN ethernet port of the openwrt router to access the address 192.168.1.1
• go to network tab → interface → device → bridge VLAN. add vlan 35 and select tag to WAN ethernet port
• go back to the network tab → interface → select WAN port → edit → Protocol: select PPPoE → enter the username/password of the ISP provided to you → Device: br-wan.35 → save → save and apply
• Wait a while to see the ipv4 address on the WAN port. you succeeded.

Method 2 only uses SFP. (Because I couldn’t setup GPON S/N on SFP, I configured it based on method 1 which is using a converter and I don’t know why, if you can setup GPON S/N on SFP by plugging it directly on the router then congratulations you have succeeded 50%)

• go to network tab → interface → device → bridge VLAN. add vlan 35 and select tag to WAN ethernet port
• go back to the network tab → interface → select WAN_6 port → edit → Protocol: select PPPoE → enter the username/password of the ISP provided to you → Device: br-wan.35 → save → save and apply
• Wait a while to see the ipv4 address on the WAN port. you succeeded.

Above is my experience, if there is anything wrong, please help me correct it. thanks

Watch the tutorials:

@Thanks

1. Detailed authentication configuration of SFP GPON G-010S-P/A & Huawei MA5671A running OpenWRT firmware.
2. Tutorial for beginners to replace 2.5G optical modem.
3. Replace ISP ONT/ONU - NOKIA GPON SFP G-010S-A (OpenWrt SFP 7.5.3).
4. 2.5G GPON with the Nokia G-010S-A ONT and NanoPi R6S.
5. Nokia Modem Flashing Tutorial (G-010S-A) No profiteering, if you like to tinker, do it yourself!.

[KFO (MJZ)]

@Thanks Really. You are matching your name

So should I buy this SFP only and plug it on BPI-R4 … It will work when I plug fiber optic line on this adapter? Or not .

…

I mean no need a full package with black box ? …

[ericwoud (Eric W.)]

@KFO

It will work when I plug fiber optic line on this adapter? Or not .

No, plugging is not nearly enough.

[KFO (MJZ)]

So if the plugging it is not enough… Anyone can help us with Guidelines…

Because our Dear/Friend @Thanks mentioned to use that GPON will work on our providers

Was my question is that GPON will be enough to let it work without full package or I need purchase full package

https://a.aliexpress.com/_okRtAON

If it will work without full package : what is required for configurations

[mcd007]

Thank you, I will buy the recommended device. As soon as it arrives and I carry out the tests, I will get back to you saying if everything went well.